Introduction:P+F/P+F/Double Blessing Ultrasonic Direct Detection Sensor UB400-F77-E0-V31 Working Voltage 20 ... 30 V DC, ripple 10 %SS ; 12 ... 20 V DC sensitivity reduced to 90%; Output Type: 1-way switch output E0, NPN, normally open.
Product parameters
Sensing range 25 ... 400 mm
Adjustment range 40 ... 400 mm
Dead Zone 0 ... 25 mm
Standard target plate 20 mm x 20 mm
Transducer frequency approx. 300 kHz
Response delay ≤ 75 ms
Permissible cable length up to 300 m
Yellow LED Switch Status and Flashing: Teach
Rated operating voltage 24 V DC
Operating voltage 20 ... 30 V DC, ripple 10 %SS ; 12 ... 20 V DC sensitivity down to 90%
No-load current ≤ 20 mA
The time delay before usability is ≤ 150 ms
Output Type: 1-way switch output: E0, NPN, normally open
Rated operating current 200 mA, short-circuit/overload protection
Voltage drop ≤ 2 V
Repeatability ± 1 mm
Switching frequency 5 Hz
Range hysteresis type 4 mm
Off-state current ≤ 0,01 mA
Temperature affects 0,17 %/K
Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Impact resistance 30 g , 11 ms cycle
Vibration resistance 10 ... 55 Hz with an amplitude of ± 1 mm
Connection type M8 x 1 connector, 4-pin
Degree of protection IP67
material
Shell: Polycarbonate
transducers: epoxy/hollow glass sphere mixture; Polyurethane foam
Installation Position: Any location
Mass 10 g
Tightening torque of the tightening screws max. 0,2 Nm
All suppliers of 76 Technology have been strictly audited to ensure that all sources of goods come from manufacturers or formal agents. Our self-confidence stems from our strict requirements for product quality, adhere to the original **, fake one pay ten, if there is a demand, welcome to consult the delivery date and price, we will select the best quotation for you in many channels, 76 technology multi-brand one-stop procurement, save you time, worry, money.
The above is P+F/Beijiafu ultrasonic direct detection sensor UB400-F77-E0-V31 products, the purpose of 76 technology is to survive by quality, develop by reputation, and eternal by service, give us a chance and give you a surprise.
|
More on that
|
P+F/Capacitive sensor CJ4-12GK-N-10M with a rated voltage of 8V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Inductive sensor NBN30-U10-E2 has a working distance of 30 mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F/Through-beam photoelectric sensors LD31/LV31/76a/115/136
Product Description: Thru-beam sensor, 30 m detection range, red, low, DC version, 2 push-pull outputs, transmitter off, fixed cable, high visibility LED, powerful push-pull output, compact and stable housing, degree of protection II
Our customer-centric ...
|
|
P+F/Capacitive sensor CBN15-F64-A0-V31 non-flush 15mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/NJ1.5-PD-E02-1.250-V95 1,5mm
Introduction: NJ1.5-PD-E02-1.250-V95 inductive sensor proximity switch adopts 4-wire DC anti-welding interference design, the sensing range is 1.5mm, and the rated value is 3000psi.
Product Details
Switch function ...
|
|
P+F Isolation Barrier K Series 35mm DIN Rail
Introduction: The widely used K series intrinsically safe isolation grid adopts DIN rail installation, which is flexible and convenient. The intrinsically safe barriers of the K series can be easily plugged into the power rails assembled with the DIN rails. This installation method can greatly save ...
|
|
P+F/Encoder RVI58N-*******1 Incremental
Introduction: An incremental encoder provides a fixed number of pulses in one revolution, and the speed is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. The accuracy of incremental encoders depends on mechanical and electrical factors ...
|
|
P+F/Capacitive sensor CBN5-F46-E2-10M 5mm
Introduction:P+F Capacitive Sensor CBN5-F46-E2-10M Flat Housing; reverse polarity protection; Fixing slot for cable tie, through-hole for screw mounting, cULus listed, general use.
Product parameters
...
|
|
P+F/Inductive sensor NBN4-12GM40-E2-T-V1 mass 12g
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F/Through-beam photoelectric sensor LA39/LK39/31/40a/116
Introduction: P+F/Beijiafu through-beam photoelectric sensor LA39/LK39/31/40a/116 bright/dark on, switchable; Mounting accessories are available; The degree of protection is IP67. Inductive range adjuster, bright/dark switch.
Products...
|
|
P+F/Double Sheet Sensor UDC-18GM50-255-3E1 Current < 65 mA
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
P+F inductive sensor NBB2-V3-E2 normally open 2 mm
Introduction: Inductive proximity sensors are the most advanced products for most applications, ranging from mechanical instruments and automation equipment to the need for high-precision, non-contact detection of metal targets. As a market leader for this type of product, we offer our customers innovative and high-quality inductive ...
|
|
P+F/Inductive sensor NBN30-U1-A0/A2 non-flush 30mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F capacitive sensor CJ10-30GM-WO with a working distance of 10mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Background Suppression Sensor MLV41-8-HV-60-IR-5360
Product Description: Visolux/ Pepperl+Fuchs has developed a range of special sensors for industrial use that extend the range of applications for common sensors. These special photoelectric sensors allow the customer to find a more suitable solution.
Specifications:
...
|
|
P+F inductive sensor NBB2-12GM50-E3-V1 2 mm
Introduction: Smooth or threaded stainless steel cylindrical housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR output mode to ...
|
|
P+F inductive sensor NBN5-F7-E0 5 mm non-flush
Introduction: P+F inductive sensor NBN5-F7-E0 5 mm non-flush, switch function normally open (NO), output type NPN, rated working distance 5 mm, installation non-flush, output polarity DC, ensure operating distance 0 ... 4,05 mm
...
|
|
P+F/GJF retro-reflective sensor GLV18-55/115/120
Product Description: Retroreflective sensor with polarization filter, M18 threaded housing design, plastic housing, front optical face, 4 m detection range, red light, light and dark on, DC type, 2 PNP output, fixed cable, high-efficiency wire in M18 plastic housing Standard application, very high detection range
|
|
P+F/Background Suppression Sensor RL31-8-H-800-RT/73C/136
Product Description: Triangulation Sensor, Standard Application Background Suppression, Large Housing Design, 800 mm Adjustable Detection Range, Red Light, Low Light, Push-Pull Output, M12 Plug, Cost-Optimized Series for Standard Tasks, Small Housing Large Construction, High Visibility Indicator, Low Target Color ...
|
|
P+F Inductive Sensor NBB8-18GM60-US 8mm
Summary: Inductive proximity sensors are the product of choice for most applications that require the precise and non-contact detection of metal objects in machinery or automation. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality inductors.
|
|