Product Introduction: Thru-beam sensor, M18 threaded housing design, plastic housing, front optical face, 20 meters detection distance, red light, light and dark, DC version, 2 PNP outputs, M12 plug, high efficiency line, short M18 plastic housing application, very high detection range, 4 LED indicators 360° visibility, version with front optical surface, DC voltage version.
Benefits: | | Through-beam sensor, M18 threaded housing design, plastic housing, front optical face, detection range 20 m, red light, bright/dark, DC version, 2 PNP outputs, M12 plug |
System composition | | Emitter | GD18 / 159 | | Receiver | GV18 / 73/120 | General specifications | | Effective detection range | 0 to 20 m | | Threshold detection range | 25 meters | | light source | LED | | Light | Modulated visible red light, 640 nm | | Spot diameter | Approximately 1300 mm at 25 m | | Divergence angle | Approximately 3° | | Optical face | Frontal | | Ambient light limitations | 30,000 lux | Functional safety-related parameters | | MTTF d | 630 pcs | | Task Time (TM) | 20 pcs | | Diagnostic Scope (DC) | 0％ | Indicator/operating device | | Operation indicator | LED green, solid power on | | Function indicator | Receiver: LED yellow, lights up when the beam is free, flashes when the stability control is insufficient; Extinguishes when the beam is interrupted | Electrical Specifications | | Operating voltage | DC 10 ... 30 V | | No-load supply current | <20 mA | Output | | Switch mode | Light/dark | | Signal output | 2 PNPs, complementary, short-circuit protected, open-collector | | Switching voltage | up to 30 V DC | | Switching current | Up to 100 mAh | | Voltage drops | ≤ 1.5 VDC | | Switching frequency | 500 Hz | | Response time | ≤ 1 ms | consistency | | Product standards | EN 60947-5-2 | Approvals and certificates | | Ingress protection | II. Rated insulation voltage ≤ 50 V AC, pollution class 1-2, according to IEC 60664-1 | | UL recognized | cULus listed, Class 2 power supply, Type 1 cabinet | | CCC certification | Products with a rated voltage of ≤ 36V do not require CCC certification/marking | Environmental conditions | | Ambient temperature | -25 ... 60°C（-13 ... 140°F） | | Storage temperature | -40 ... 70°C（-40 ... 158°F） | Mechanical Specifications: | | Ingress protection | IP67 | | connect | 4-pin M12 x 1 connector | | material | | | housing | personal computer | | Optical face | Polymethyl methacrylate | | connector | plastics | | Mass | Approximately 10 grams per device |
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only when every process, every action and every detail of the service is professional and careful, can we meet or even exceed the expectations of customers, so that customers can be satisfied and recognize us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces P+F/G18/GV18/73/120 products, if you are interested in P+F/G18 G18/G18/G18/G18/G18/G18/G18/G18/G18/G18/G18/G18/G18/G18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv18/Gv
|
More on that
|
P+F/Capacitive sensor CBN8-F64-E1 8mm non-flush
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/M100/MV100-6090/102/115 through-beam photoelectric sensors
Product Introduction: Thru-beam sensor, miniature design, miniature sensor light forming slit, easy to use, very bright, high visible light point, full metal threaded mounting.
Our customer-centric service concept: the pursuit of a full range of services is a ...
|
|
P+F/Capacitive sensor CJ4-12GK-N-10M with a rated voltage of 8V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F Retroreflective Sensor ML100-55/95/102 5m detection range
Description: Retroreflective sensor ML100-55/95/102 photoelectric sensor with polarization filter, plastic housing, 5 m detection range, red light, adjustable sensitivity, light/dark, DC type, NPN output, M8 plug.
...
|
|
P+F/Capacitive sensor CBN7-F46-E1-Y291652 3-wire DC
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Inductive sensor NCB1,5-8GM25-N0-Y295009
Introduction: Smooth or threaded stainless steel housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indication; M8, M12 connector connection or terminal wiring; PVC, PUR or silicone cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR...
|
|
P+F/Slot sensor GL-ES-IR /115/120 60V DC
Product introduction: There is a special through-beam sensor in our products called fork sensor. It is mainly used in places where the measurement distance is short. Since only one device requires wiring, fork sensors have the advantage of being easy to install compared to standard control sensors. ...
|
|
P+F/OBE20M-R100-S2EP-IO-V31-L through-beam type
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F/The capacitive sensor CJ10-30GK-WO has a working distance of 10 mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/UB1000-18GM75-E5-V15
Product Introduction: The transducers used to transmit and receive sound waves are separated, so that the system does not need to wait for the signal attenuation of the transmitter, thus effectively reducing the dead zone. The direct detection type of ultrasonic sensors is available with switching and analog outputs. Direct detection of all support window mode functions ...
|
|
P+F inductive sensor NBB1,5-8GM40-Z0 1.5 mm
Introduction: Inductive proximity sensors are the preferred product for most applications that require non-contact, accurate detection of metal objects in mechanical or automated equipment. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality ...
|
|
P+F/Inductive sensor NBN4-12GM50-E1 with a housing diameter of 12 mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
Germany P+F/Capacitive sensor CBB4-12GH60-E0-V1 with a voltage drop of ≤ 2,5 V
Description: Germany P+F/Capacitive sensor CBB4-12GH60-E0-V1 Voltage drop≤ 2,5 V, output type: PNP, reverse polarity protection: reverse polarity protection, no-load current: ≤ 12 mA
peculiarity
4 mm, flush
The working distance can be adjusted via a potentiometer
...
|
|
The P+F incremental encoder AH40 weighs approx. 160 g
Introduction: Incremental Encoder AH40, Industry Application: Textile Machinery, Bending Machinery, Printing Machinery, Metallurgical Industry, Elevator Product Structure: Empty Row Shaft, Outer Diameter (mm): 40mm, Bore Diameter/Shaft Diameter (mm): 8mm, Resolution (CPR): 1-1024 PPR, Working Voltage: 4,75... 30 V D ...
|
|
P+F/DK12-11/124/136 M12 plug
Product introduction: The characteristics of P+F color mark sensor are: low contrast detection under high resolution, short response time; It is not sensitive to the deviation of the height and angle of the detected material; The optical lenses are 90° interchangeable. Just press the TEACH-IN button and the emitter LED will automatically select the best ...
|
|
P+F/Capacitive Proximity Sensor CBN15-F64-E2 15mm
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
...
|
|
P+F capacitive sensor CBB10-30GKK-A2 10mm flush
Introduction:P+F Capacitive Sensor CBN5-F46-E2-10M Flat Housing; reverse polarity protection; Fixing slot for cable tie, through-hole for screw mounting, cULus listed, general use.
Product parameters
...
|
|
P+F/Beam Ultrasonic Barrier UBEC300-18GH40-SE2-V1
Introduction: An ultrasonic through-beam sensor consists of a transmitter and a receiver mounted facing each other. Ultrasonic through-beam sensors work by emitting sound waves from the transmitter to the receiver to detect objects through the sound beam being interrupted by the target object. The emitter produces ultrasonic ...
|
|
P+F/Through-beam photoelectric sensor BB10-P/59/76b/103/115e
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F/VLD700-F280-2E2-1000 laser diode
Product Introduction: Parameterization of the SmartRunner Detector is very simple. The laser line of the vision sensor is projected onto the desired background and programmed using teach-in. With the Data Matrix control code, the user can set additional parameters such as the detection area without a PC ...
|
|
Contact
working hours
