Introduction to the advantages and disadvantages of Sick Sensors - thermistor temperature sensors

Resistance, inductance and capacitance are the three major types of passive components in electronic technology, and a capacitive sensor is a sensor that converts the measured change into a capacitance change, which is essentially a capacitor with variable parameters. Capacitive sensors offer the following advantages: (1) ...

As an expert in smart sensors, Sick has teamed up with SATO, a world-renowned manufacturer of printing and recognition solutions. Through the on-site practical application cases, not only the technical characteristics of SICK & SATO were demonstrated, but also the possibility of integrating barcode and RFID technology in the automated production line at the same time.

SICK sensors are sensors that use a photoelectric element as a detection element. It first converts the measured change into a change in the optical signal, and then further converts the optical signal into an electrical signal with the help of an optoelectronic component. Photoelectric sensors are generally composed of three parts: light source, optical path and optoelectronic components.

1. In order to have sufficient heat exchange between the measuring end of the RTD and the medium to be measured, the location of the measuring point should be reasonably selected, and the installation of RTD near the valve, elbow, pipe and equipment should be avoided as much as possible. 2. The thermal resistance with a protective sleeve has heat transfer and heat dissipation loss, in order to reduce the ...

In the packaging, electronics and other industries, there has always been a need for stable detection of specific colors to meet the needs of positioning, counting, etc. This is where a color sensor is often used. If the installation space is small, a color sensor of the miniature size type is required. This is why the miniature color sensor from SICK – CS ...

Analysis of the factors that may cause the zero point change of the SICK sensor: overload will lead to a sudden change in the zero point, and the output resistance will obviously exceed the specified value impact, as above; Moisture return or turbidity, so it is mainly manifested as a continuous change of 0 point, high and low, etc., at this time, the ground resistance will be further reduced - in ...

Photoelectric sensor is a small electronic device, a key element to end the photoelectric conversion in various photoelectric detection systems. It is a sensor that uses the various properties of light to detect the presence or absence of objects and changes in the surface state. Photoelectric sensors are non-contact, fast responding, and functionally reliable.

1. The pressure goes up, the output of the transmitter does not go up to this situation, you should first check whether the pressure interface is leaking or blocked, if you admit that it is not, check the wiring method and check the power supply, if the power supply is normal, then simply pressurize to see if the output changes, maybe observe whether the zero position of the sensor has an output, if there is no ...

Dynamic features: The so-called dynamic characteristics of the sensor refer to the characteristics of the output of the sensor when the input changes. In practice, the dynamic characteristics of a sensor are often expressed in terms of its response to some standard input signal. This is because the sensor's response to a standard input signal ...

1. Two-wire system: the way to connect a wire at both ends of the thermal resistance to draw out the resistance signal is called the two-wire system: this lead method is very simple, but because there must be a lead resistance r for connecting the wire, the size of R is related to the material and length of the wire, so this lead method is only applicable to ...

Infrared sensors are sensors that use the physical properties of infrared rays to make measurements. Infrared, also known as infrared light, has the properties of reflection, refraction, scattering, interference, absorption, etc. Any substance that has a certain temperature above absolute zero can radiate infrared rays. ...

1. There is a difference between two-wire system and three-wire system for proximity sensors, and three-wire proximity sensors are divided into NPN type and PNP type, and their wiring is different. 2. The wiring of the two-wire proximity sensor is relatively simple, and the proximity sensor and the load can be connected to the power supply after being connected in series. 3. Three-line ...

It is possible to bypass small obstacles (such as dust) (photoelectric is completely not allowed in this environment). Liquid position can be measured. (e.g. for level monitoring) Transparent objects can be measured. (e.g. presence or displacement of glass) Not affected by the surface of the object ...

Photoelectric sensors A photoelectric sensor is a device that converts an optical signal into an electrical signal. Its working principle is based on the photoelectric effect. The photoelectric effect refers to the phenomenon that when light hits some substance, the electrons of the substance absorb the energy of the photons, and the corresponding electrical effect occurs. According to the photoelectric effect ...

1. Measurement Sensors and sensor systems from SICK measure dimensions, oversights, volumes, distances, speeds, and filling levels and then ensure that the process runs smoothly. 2. Detection SICK sensors are able to detect the presence or absence of various objects as well as the quality of consumer products to the satisfaction of ...

1. The color sensor, also known as the color sensor, is a machine that compares the color of the object with the reference color that has been taught earlier to detect the color. The standard color measurement method is to use a spectrophotometric colorimeter to measure the tristimulus value of the sample, so as to obtain the color of the sample.

01 Temperature sensor Temperature sensors measure the heat energy in a heat source, allowing it to detect temperature changes and convert those changes into data. Machinery used in manufacturing often requires a specific level of ambient and equipment temperature. Similarly, within agriculture, soil temperature is ...

With the rapid development of industrial automation in recent years, machine vision, as a smart brain endowed with "eyes" to machines, has been widely used in various fields of intelligent manufacturing. In the context of the rapid penetration of artificial intelligence in the Internet and emerging industries, traditional industries are also constantly promoting intelligent ...

1. First of all, the front face of the photoelectric sensor must be parallel to the surface of the workpiece or object to be detected, so that the conversion efficiency of the photoelectric sensor will become high. 2. When installing and welding, the small distance between the root of the pin of the photoelectric sensor and the pad shall not be less than 5 mm, otherwise ...

Infrared sensors are sensors that use the physical properties of infrared rays to make measurements. Infrared, also known as infrared light, has the properties of reflection, refraction, scattering, interference, absorption, etc. Any substance that has a certain temperature above absolute zero can radiate infrared rays. ...