Estun servo motor – the cause of overheating of servo motors

Generally, it means that the machine encounters an error or emergency shutdown and needs to be overhauled and maintained. Here's how to solve it: 1. Check if the power supply of the teach pendant is normal, if there is a power supply problem, it may cause the machine to stop in an emergency. 2. Check if there is an object inside the machine ...

1. Open the shell of the robot to expose the motor base. 2. Use a screwdriver or wrench to remove the screws on the motor base. 3. Remove the screws, lift the motor base, and disassemble it from the robot. 4. The motor base is tightly connected with the robot, and tools such as wrenches are used.

From the perspective of the protection response speed of the robot servo drive, Estun has a small amount of calculation in the form of torque, and the response to the control signal of the drive is fast. The azimuth form has a large amount of computation, and the response to the driver's control signal is slow. 1. If there is a relatively high demand for dynamic functions in sports...

1. Regularly check the encoder connection line of the servo motor and the power connector of the servo motor to confirm that they are firmly connected; 2. If the servo motor is connected to a reduction gear, the servo motor should be sealed with oil to prevent the oil from the reduction gear from entering the servo motor. ...

A51: The robot spindle servo motor is abnormal. It could be a cable failure, a servo drive problem, a damaged spindle bearing, etc. A47: The servo motor is overheating. It may be because the external ambient temperature is too high, the servo motor is starting to break, and it cannot be cooled properly. A4 ...

Cause of failure and solution: (1) The phase sequence of the motor is out of order and the encoder is abnormal, check whether the power line of the motor (U, V, W, D) is connected incorrectly, and whether the encoder connection is not in good contact. (2) The motor model parameters do not match, check and reset the server Pn parameters or more...

Servo system has an important position in electromechanical equipment, and high-performance servo system can provide flexible, convenient, accurate and fast drive. With the advancement of technology and the continuous development of the entire industry, the development trend of the traction system is to replace the traditional hydraulic, DC ...

26. Is it possible to install the mover coils of multiple brushless motors on the same magnetic track? OK. As long as the movers do not interfere with each other. 27. What are the advantages of using linear motors over ball screws? Since there is no ...

One: machine cleaning First and foremost, disconnect the power supply and remove debris around the machine. Use a clean cloth to wipe the surface of the machine to ensure that it is free of dust, grease and other impurities. For the cleaning of the inside of the machine, it needs to be operated by professionals. Two: Look at the machine parts ...

1. Position mode Look at this name, you can guess a rough idea, to put it bluntly, the position requirements are relatively high, such as the linear servo module this kind of mechanism, the need for the sliding mechanism to stop accurately, just use this mode, speaking of which, let's take a look at the ball screw module ...

Precautions for servo motors: 1. Protection of servo motor oil and water A: The servo motor can be used in places where it will be attacked by water or oil droplets, but it is not fully waterproof or oil-proof. Therefore, servo motors should not be placed or used in water or oil-infested environments. ...

1. Applicable welding methods and cutting methods: Generally, arc welding robots are only suitable for MIG/MAG welding, and there is no interference of high-frequency arc striking on the control and drive system of the robot. Whether it can be used for tungsten argon arc welding depends on whether the robot has a special anti-interference method.

1. Overload alarm A04 1. The wiring of the servo motor is wrong or the wiring is leaking (1) The U, V, and W phase wires of the motor are connected incorrectly (2) Whether the insertion of the connector on the servo motor side is defective 2. The type of servo drive and motor does not match View drive type ...

Servo motor refers to the engine that controls the operation of mechanical components in the servo system, and is a kind of auxiliary motor indirect transmission device. The main function is to use it in a closed ring, transmit the signal to the system at any time, and at the same time correct its own operation with the signal given by the system. Servo motor ...

1. The palletizing robot is mostly four-axis, flexible in operation, and the load can reach 180 kg. 2. It can carry out high-precision handling and palletizing work, save a lot of labor for enterprises, and promote modern production. 3. Customized according to the on-site needs of the enterprise, high work efficiency, 24 hours uninterrupted...

There are many types of motors, and the ordinary motor we commonly use is the induction motor, although it and the servo motor are both motors, there are certain differences: 1. The speed of ordinary motors is too fast, the torque is too small, and because there is no feedback from itself, it is usually impossible to achieve accurate control.

Problem 1: The reason why the servo motor alarms the overload If the drive resistance is too great, check the drive system. Q2: What is the difference between stepper motor and servo motor overload capacity? Question 3: Is the servo motor overload necessarily related to the current? As the motor torque output ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure: (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring of the control equipment is incorrect. 2. Failure ...

On September 25, 2020, a group of 20 people from the Industry and Information Think Tank Alliance, led by Comrade Fan Bin, Deputy Director of the Department of Political and Legal Affairs of the Ministry of Industry and Information Technology, visited Estun Company for research. Dr. Wang Jiegao, President of Estun Automated Robot Research Institute, and Ms. Yuan Qin, Deputy General Manager, accompanied the visit and investigation. The experts visited ...

The position data of each axis of the industrial robot is stored through a backup battery, which should be replaced regularly (one and a half years). In addition, if the backup battery shows a voltage drop alarm, the battery should also be replaced in time. 1. Replace the controller motherboard battery Program and system variables are stored in the main ...