Verun Tong Touch Screen cMT Series (CloudHMI For Industry 4.0)

1. Software editing-system parameter setting-HMI attributes-port number: 8000 change, such as 9000; 2. Bring up the computer task manager - end com_e30.exe under the process; 3. Restart the computer; 4. Query other occupancy on the computer through TCPview software.

The industrial touch screen is a resistive screen, which is better than the capacitive screen anti-interference, but generally if there is no response, most of the touch glass on the outside (generally called the touch board) is broken, and it is good to replace it directly, of course, the following problems are not excluded: 1. The touch screen and PLC are generally used together, and the ...

1. Why can't the screen display Chinese normally, but the display is garbled? Answer: This situation is generally caused by not choosing the correct Chinese font, just choose a Chinese font, the specific operation steps are as follows: 1) In EasyBuilder soft...

1. Open the Weiluntong editing software, and click Event Login in the pop-up menu bar on the right. 2. On the edit page of event login, we click the new button below, and then a setting page for alarm login will pop up.

1. Do not hit with metal objects. Usually the HMI will be covered with a layer of glass to protect the screen and make it easy to touch. However, the glass is fragile, do not hit the screen with metal objects during use, it is easy to cause the glass to be scratched or broken. 2. Avoid squeezing the screen with heavy objects. Around HMI ...

1. Dispose of dirt and grease on the touch screen The accuracy of the screen is a characteristic of grease build-up on the surface, which can make it cumbersome to type the correct commands. In addition, due to the accumulation of dust caused by overheating, the internal components of industrial computers may not work properly. The use of microfiber ...

1. The motherboard cannot recognize/display the peripheral devices. 2. The peripherals will stop working for a few seconds or more. 3. A slow boot may indicate that your motherboard is broken, although it could also be other components. 4. The touch screen does not recognize the flash drive, or ...

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...

Four-wire: Because of factors such as cost and mature technical level, four-wire touch screen is almost the most basic production specification for touch screen practitioners. First of all, in terms of resistive touch screen technology, four-wire touch screen accounts for more than 50% of the market. It is composed mainly ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. However, when configuring, you can disable this button in the software system settings. 2. Set the system bit LB-9020 in the touch screen to ON...

1. Novelty of operation The capacitive touch screen supports multi-touch, making operation more intuitive and fun. 2. It is not easy to be touched by mistake Because the capacitive touch screen needs to sense the current of the human body, as long as the human body can operate it, there will be no ...

1. Enter the system settings interface of the Weilun touch screen, and select the "Power Management" option in the "System Settings". 2. In "Power Management", you can set how long the touch screen will automatically enter the "standby" state without operation, and you can also set how long it will enter the "...

1. Connect your Veriton device and open the software to enter the data point configuration page. 2. On the Data Point Configuration page, select the data point that you want to scale. 3. Click the "Settings" button and select "Scale Factor Conversion" in the pop-up window. 4. ...

1. SPI interface Serial Peripheral Interface (SPI): Serial peripheral interface. It was first defined by Motorola on its MC68HCXX series of processors. It enables the MCU to communicate serially with various peripherals to exchange information. The SPI has three registers ...

1. The line interface of the Weilun Tong touch screen is faulty. 2. Whether there is a crack fault on the surface of the touch screen. 3. External interference and control box failure. 4. The connection between the touch screen and the host or the host is faulty. ...

1. First of all, open the created Weilun touch screen project, select Common in the menu bar and click Open. 2. Secondly, select the system parameter icon in the common drop-down menu and click to open. 3. Finally, click Change. ...

Weiluntong contact screen repair 　　The first step in troubleshooting a touchscreen system is to determine if the problem is related to the display, software, or hardware: Don't confuse the visibility issue with the contact screen issue, the two are unrelated. Software problems are caused by fundamental hardware functions ...

1. First of all, open the Weiluntong touch screen and enter the application. 2. Secondly, select "Edit" → "Personalization" on the control bar of the window. 3. Finally, set the picture to the bottom layer. ...

1. MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Second, MT500, this model is the successor of the previous model, after the launch of the very good sales results. ...

1. Appearance of Weiluntong contact screen: Use special Weiluntong contact screen cleaner and soft fiber cloth to clean the appearance of Weiluntong contact screen, remove dirt and fingerprints, etc., to ensure a clean appearance. 2. Restart the device: test to restart the contact screen device of Weiluntong, sometimes restart...