The connection of Mitsubishi 5U PLC and Kunlun Tongtai touch screen

Create Date: 2024-8-30 12:03:23|Source: Kunlun Tongs/MCGS

First of all, let's take a look at the interface settings of the Kunlun Tongtai touch screen.

1. Click on the device window to enter the Add PLC

2. First add a TCP parent serial port, and add a 5U device below

3. Double-click the TCP parent device to learn the settings, enter the IP address of the touch screen itself, and select the local port number, which is generally 0, and will automatically assign its own port number. Then fill in the IP address of 5Uplc, it must be in the same network segment as the touch screen (you can go under Baidu if you don't understand the meaning of the same network segment), fill in the port number specified by the 5U touch screen, which should be consistent with the PLC, and it is written here as 1051

Let's set up the PLC side below

1. Enter the Ethernet port settings and set the IP address of the PLC

2. Click "Target Device Connection Configuration Settings" to configure it in detail. Select an SLMP (and touch screen connection) device from the general Ethernet device on the right, and fill in the port number 1051 (generally select more than 1000, and communicate with a device needs to correspond to a different port number)

3. Remember to click OK after exiting, otherwise the parameters will not be saved

Finally, be sure to click "Apply", and then plug in the network cable, and the touch screen and PLC can communicate

The connection of Mitsubishi 5U PLC and Kunlun Tongtai touch screen

More on that

	Kunlun Tongtai touch screen - analysis of common fault phenomena of surface acoustic wave touch screen Fault 1: Touch deviation Phenomenon: The position of the finger does not coincide with the mouse arrow. Analysis: After installing the driver, there was no vertical touch to the bullseye center position when correcting the position. Solution: Recalibrate the position. Fault 2: Touch ...
	Kunlun Tongtai touch screen program modified how to maintain additionally 1. In the Device window, click Select the device created by the variable. 2. Select the device configuration view option in the device editing window to check whether the configuration is correct. 3. When it appears, click OK when the device is viewed correctly. 4. Then select the OK button to save the data. ...
	Common problems and solutions of communication of Kunlun Tongtai MCGS touch screen (61-65) 61. 200PLC: What is the reason for the communication status jump (1) Whether the communication delay setting is too short, and set the appropriate delay time; (2) Whether there is interference on site, shielded wire and grounding can be used; (3) Refer to PLC "SMW22", see PLC running program ...
	How to set the Kunlun Tongtai touch screen and PLC communication is normal 1. First of all, open the Kunlun Tongtai touch screen software, find the [User Window] and click to open. 2. Then select [New Window] to create two windows. 3. Then in the page that opens, click [Window 0] to enter the window. 4. Then in the toolbox ...
	Can Kunlun Tongtai touch screen run in the computer embedded version? Kunlun Tongtai touch screen is a touch screen controller, which is generally used in embedded systems, such as industrial computers, embedded computers, intelligent terminals, etc. If you want to connect it to your computer to run, you can try the following methods: 1. USB interface: Kunlun Tongtai touch screen ...
	The reason for the communication failure between Kunlun Tongtai touch screen and Mitsubishi PLC Communication failures are generally due to three factors (1) Communication parameters, such as the COM number of the serial port, baud rate, etc., the IP address of the network port, etc. (2) Communication line, such as RS232 communication, the result is RS485. For example, it is directly connected to the network port, but it is connected to the cross. （3 ...
	Kunlun Tongtai touch screen - what are the characteristics of touch screen? (1) Simple operation Just touch the corresponding indication button on the touch screen with your finger to enter the information platform. (2) User-friendly interface Users can operate according to the information and instructions indicated on the screen even if they do not have computer-related expertise. ( 3） ...
	Introduction to Kunlun Tongtai touch screen programming software Kunlun Tongtai touch screen programming software is a very professional configuration software. This program is very robust and suitable for the engineer profession, which can perform a variety of functions such as rapid data collection, detection, front-end data processing and control, and it can also be used with all kinds of mainstream collection boards.
	The solution of Kunlun Tongtai touch screen booting white screen and unable to connect to the computer 1. First on the computer, use the right mouse button on My Computer - Properties to open the properties page, and then find and select the advanced system settings option in this page. 2. Then in the dialog box that opens, switch to Hardware Options. 3. Then under the hardware options, look for ...
	Kunlun Tongtai touch screen arrived in large quantities Kunlun Tongtai touch screen arrives in large quantities, can be easily matched with Siemens PLC, details can be consulted There is a stock model TPC1061TI TPC1071GI TPC1561HII TPC1570GI TPC7062TI TPC7072GI ...
	The configuration structure of Kunlun Tongtai McgsPro software was introduced from the overall structure The McgsPro architecture is divided into three parts: configuration environment, simulated operation environment, and operation environment. The configuration environment and the simulated operating environment are equivalent to a complete set of tools and software, which can be run on a PC. Users can ...
	Introduction to the characteristics of MCGS Kunlun TPC series touch screen Small capacity: The speculative configuration of the whole system requires only a very small storage space, which can be easily used with DOC storage devices; High speed: The system has high time control accuracy, and can easily complete various high-speed acquisition systems to meet the requirements of real-time control systems. Low cost: ...
	Steps to upload the program on the Kunlun touch screen 1. Install the MCGS configuration software on the computer first, then find the power supply to supply power to the touch screen, connect the screen with the computer with the communication cable, and upload it in the software. 2. After we install the software, first go to open the software, and then in the drop-down option of the file menu, select ...
	Kunlun Tongtai touch screen - six different classifications of touch screens 1. Resistive touch screen Analog resistive screen The analog resistive touch screen is what we usually call the "resistive screen", which is a kind of touch screen that uses pressure sensing to control. It is made of two layers of ITO plastic film coated with conductive function, and the two ITO are equipped with microparticle supports.
	How to change the model of Kunlun Tongtai touch screen First of all, on the back of the Kunlun Tongtai touch screen, determine the specific model of the Kunlun Tongtai touch screen. Open the Kunlun Tongtai touch screen programming software, click [File] in the menu bar and open it. In the File drop-down menu, select Project Settings In the pop-up Modify Project ...
	How to replace the external screen of Kunlun Tongtai touch screen? 1. Stuff preparation 1. 1 Phillips screwdriver; 2. 1 small slotted screwdriver; 3. 1 hair dryer; 4. Several transparent double-sided tapes. Second, the old screen is dismantled 1. Use a Phillips screwdriver to remove the 6 screws on the back cover and open the back cover. 2. ...
	How to enter the system settings of the Kunlun Tongtai touch screen One. Kunlun Tongtai touch screen touch calibration: 1) When the TPC Kunlun touch screen is powered on and started, when the progress bar appears, click the touch screen, and the [Startup Properties] dialog box will pop up, and wait for 30 seconds to automatically enter the touch calibration interface; 2) According to the prompts of the [Touch Screen Calibration] program ...
	The common problem handling process of Kunlun Tongtai touch screen 44. Clear the configuration engineering password flow (1) Record customer information: including the name of the unit, the name of the customer, the contact number, ask the customer for the configuration project and require the customer to provide the certificate with the official seal and the purchase channel; Attestation File Format: Our company is XXX, ...
	Kunlun touch screen IP address view and setting 1) After the above touch calibration is completed, click [Enter Operating System] in the [Startup Properties] dialog box to enter the operating system; 2) Click [Start] --> [Settings] --> [Network & Dial-up Connection]; 3) Double-click [DM9000A] to bring up the corresponding dialog box, ...
	Hardware Problems and Solutions of Kunlun Tongtai MCGS Touch Screen(91-95) 91. How to update the TPC splash screen After the project is downloaded and the communication test is successful, click "Advanced Operation", in the advanced operation dialog box, select the corresponding file to replace the startup screen, and then click the "Change Startup Screen" button. Note: The splash screen is set ...