PLC input and output circuit debugging - Xinjie

Switch Mode Power Supply (SMPS) will cause the base of the switch tube to fail to get the switching pulse and intermittent operation due to the short circuit of the load, the failure of the vibration circuit itself and the loss of control of the protection circuit, which makes it difficult to locate the shortcomings of SMPS. Difficult to repair ...

1) Investigation and investigation of problem phenomena. There are many kinds of inverter problem phenomena, for example, the same type of problem may have different problem phenomena, and different types of problems may have the same problem phenomenon, which brings difficulties to find the problem. However, the problem phenomenon is the basic basis for overhauling the inverter ...

1. The cause of the leakage problem Some sites use frequency converters to control the motor, which will present the problem of leakage, and the leakage voltage ranges from tens of volts to 200 volts. In view of this problem, the reason for this problem is explained and stated as follows. Depend on...

The frequency converter is a power converter in the motion control system. Today's motion control system includes many technical fields, and the general development trend is: communication drive, high-frequency power changer, digital, intelligent, and networked control. VFDs are power converters in motion control systems. ...

Since the advent of the MS6 series B1 and B2 servo motors, they have been widely recognized by customers for their outstanding performance advantages, and their performance in terms of temperature rise, overload ability, overspeed range and protection level is far better than that of MS5 series servo motors. This MS6 series B3 motor released will ...

For the 130 frame same service motor, the MS6H-130 series high inertia servo motor previously launched by Xinjie is mainly used in large inertia load occasions, in order to enrich the application scenario, the MS6G-130 series medium inertia servo motor is launched, which is suitable for DS5 series servo drive ...

In the process of century industry, the more top-level software and hardware planning for the suspension of frequency conversion skills, first according to the characteristics of traditional air compressor motors, comprehensively analyze the causes of energy consumption and operation characteristics, so as to plan the control of frequency conversion skills speed regulation, air skill tightening, pressure sensing skills improvement, etc.

The most direct cause of cable problems is the breakdown due to the loss of insulation. First of all, there are: a. Overload operation. Long-term overload operation will increase the temperature of the cable, aging the insulation, resulting in breakdown of insulation and degradation of construction quality. b. Electrical: the construction process of the cable head does not meet the requirements.

Programmable manipulators (PLCs) have always played an important role in industrial field control. With the increase of the state's investment in the water supply profession, the level of automation of water plant operation has been continuously improved, and the use of PLC in the water supply profession has gradually increased. The touch screen is used with the PLC, so that the operation of the PLC ...

1. Air opening: a total air switch, which is the power control of the entire cabinet. I believe that every cabinet must have one thing. 2. PLC: This should be selected according to the needs of the project. For example, if the project is small, it can be an integrated PLC, but if the project is more ...

It is necessary to route the signal line and the power line separately: When using the analog signal remote control inverter, in order to reduce the disturbance of the analog signal of the VFD and other equipment, please separate the signal line of the VFD control from the strong current circuit (main circuit and sequential control circuit). The spacing should be more than 30cm. Even in the control ...

Make accurate punctuality, read accurate punctuality, and stop accurate punctuality. Watchman number. Range: T600 - T618 (T600, T602, T604...) T618, numbered even) Punctuality. Accurate punctuality ...

The problem of the inverter is not only affected by external factors, but also by internal factors. 1. The inverter parameter setting is unreasonable and countermeasures to make the inverter work normally, in addition to the normal equipment, the parameter setting is also very important, if the parameter is not set properly, it will not be able to ...

Input and output loop debugging 1. Analog input (AI) loop debugging. Carefully check the address assignment of the I0 module; Check whether the loop power supply mode (internal power supply or external power supply) is consistent with the field instrument; Use a signal generator to add a signal to each channel at the field end, generally taking 0, 5 ...

From 14:00 to 15:20 on May 14 last year, the X-SIGHT visual brand conference with the theme of "Vision, Light Up Intelligent Manufacturing" was held online, officially announcing that Wuxi Xinjie and Intel will join hands to create a new era of intelligent manufacturing. X-SIGHT unveiled a new Intel chip-based ...

XCPPro is a professional XCPPl programming software, which is a new XC series PLC programming software, which can be used normally by making corresponding configurations in XCPPro. The software supports WindowsXP32-bit Win764-bit system. ...

The XC series includes XC1 (Economy), XC2 (Basic), XC3 (Standard), XC5 (Enhanced), XCM (Sport), XCC (High Performance) and their corresponding expansion modules. XC series PLC can be ...

(1) What is the current setting value of the thermal relay? The setting current of the thermal relay refers to its action current, that is to say, it is adjusted between 0.95 - 1.05 times of the rated current of the motor being maintained.

XC can be divided into multiple sub-series according to the incompatibility of functions, including XC1 (economy), XC2 (foundation), XC3 (standard), XC5 (enhanced) and their corresponding expansion modules, as well as special imitation ontology, activity control models, etc. Powerful function, complete variety, can be full ...

Motion control has a significant period characteristic, it is a variety of high-tech generalization, used to bring industrial automation, office automation and home automation to a higher stage. Nowadays, motion control is mainly composed of variable frequency drive (VFD), electric motor, control ...