Hollysys OCS industrial optical bus control system was successfully applied in Sinopec project

Since the day of the birth of PLC, it has occupied the core position of the entire automatic control system. There are also many discussions about the development direction of PLC, whether it is predicted that PAC will replace PLC from 10 years ago, or during this time, some people even say that PLC is no longer needed in the future Industry 4.0 era...

The choice between a programmable logic controller (PLC) and a distributed control system (DCS) is a case-by-case analysis, as the requirements for the control system vary depending on the application. You can start from the following aspects! PLC and DCS PLC ...

At 15:05 on January 12, 2022, Datang Anhui Luoneng Power Generation Co., Ltd. (hereinafter referred to as Datang Luohe) successfully completed the full-load trial operation of Unit 5 after comprehensive upgrading, marking the smooth operation of Unit 5 of Datang Luohe Power Plant after the transformation. Hollysys HOLLiAS MACS IC completely ...

1. Circuit isolation The isolation of analog circuits is more complex, mainly depends on the accuracy requirements of the transmission channel, the higher the accuracy requirements, the higher the cost of the channel; However, when the performance requirements rise to the main contradiction, the isolation components should be selected based on performance, and the ...

1. Switch logic control Switching logic control is the basis of PLC. It is the first use case and the most extensive of all. Replace the previous relay circuit control and realize logic sequence control; It can be used for the control of stand-alone equipment, and can also be used for group control and ...

In recent years, the State Administration of Safety Supervision, the Ministry of Industry and Information Technology, the Ministry of Education, and the Ministry of Finance have successively launched a number of national policies to implement major decision-making projects such as vocational skills improvement actions, safety skills improvement actions, and vocational education reforms, aiming to create a highland for the training of technical and skilled talents.

From November 15th to 17th, the 2022 China Nuclear Energy High-Quality Development Conference and Shenzhen International Nuclear Energy Industry Innovation Expo (hereinafter referred to as the "2022 Shenzhen Nuclear Expo") will be grandly reopened at the Shenzhen World Convention and Exhibition Center. 　　The theme of this year's Nuclear Expo is "Nuclear Gathering in the Bay Area, Activating the World".

1. High reliability Because DCS disperses the system control function on each computer, and the system structure adopts a fault-tolerant design, the failure of one computer will not lead to the loss of other functions of the system. In addition, due to the fact that the tasks undertaken by the various computers in the system are comparatively ...

1. What is a communication protocol? A communication protocol is an agreement between two parties to a communication. The agreement includes uniform provisions on data format, synchronization mode, transmission speed, transmission steps, error detection and correction mode, and control character definition, etc., which must be complied with by both parties to the communication. Therefore...

1. Stand-alone control system The stand-alone control system is controlled by one PLC to control one device or one simple production line, as shown in Figure 7-1. The composition of the stand-alone control system is simple, the number of I/O points required is less, the storage capacity is small, and when the model of PLC is selected, whether there is a communication network at present.

1. The configuration of the system and controller should focus on reliability and load rate (including redundancy). The communication load rate must be controlled within a reasonable range, and the load rate of the controller must be balanced as much as possible to avoid the occurrence of "high load" problems. 2. The distribution of system control logic should not be too much.

1. The function of PLC PLC is a general industrial automatic control device with microprocessor as the core, integrating computer technology, automatic control technology and communication technology, which has high reliability, small size, strong function, simple program design, flexible and universal and maintenance methods.

Resistive coupling interference In the process of work, many factories ignore the problem of wire aging. When a variety of signal lines are transmitted together, other transmission signals will be affected due to the aging and leakage of the insulation material on the wire, and other transmission signals will be interfered with. ...

01. Power supply The DCS power supply system is mostly a "dual backup hot redundant power supply", and the prevention and control of power failures is mainly reflected in the inspection and daily maintenance. Generally speaking, as long as the unit is normal ...

1. Data backup When carrying out maintenance, we must cut off the power, data backup between power outages is an important link, for the data that needs to be archived for a long time, you can back up the historical trend data to the mobile hard disk, and then turn off the Windows-based operating system (Note...

On September 20, 2022, Berlin time, the 13th Germany Berlin International Rail Transit Exhibition (InnoTrans 2022) opened at the Berlin International Exhibition Center in Germany. Following the 2018 exhibition, Hollysys once again appeared at the Berlin International Railway Exhibition (hereinafter referred to as the Berlin Exhibition) ...

1、-10—10V。 When the voltage of -10V-10V is converted to F448-0BB8Hex (-3000-3000) at 6000 resolution; At 12000 resolution, it is converted to E890—1770Hex (-6000—6000). 2、0—10V。 At a voltage of 0-10V, at a resolution of 12000 ...

01 Node bus failure The node bus material is usually a coaxial cable, so as long as there is a cable disconnected, the communication of all devices on the bus will be paralyzed, which will cause serious phenomena such as data loss, equipment stoppage and operation interruption, and may eventually directly or indirectly cause huge ...

How a PLC controller works 1. Scanning technology When the PLC is put into operation, its working process is generally divided into three stages, namely input sampling, user program execution and output refresh. The completion of these three phases is called a scan cycle. During the entire operation ...

In December 2020, the equipment of Sinopec Qingdao Petrochemical Co., Ltd. (hereinafter referred to as Qingdao Petrochemical) 5 million tons/year oil refining integration project, which was upgraded and transformed by Hollysys, was successfully operated, marking the successful completion of the DCS equipment upgrading task. This upgrade is a major development for Sinopec Industrial Holdings.