What industries is Weiluntong touch screen - touch all-in-one machine suitable for?

1、cMT3090 9.7" TFT display 1024*768 dots, brightness 350, contrast ratio 500:1, 262K color, Flash memory: 4GB memory, 1GB, DC19.2-28.8VDC power supply, four-wire resistive type, SD card slot, support SD/SDHC, USB Host USB ...

There are 2-4 hidden DIP switches on the back of the VIRONT touch screen, and each HMI backplate has a set of reset buttons and DIP switches that can be used to trigger the corresponding function when switching between different modes. The following is a list of categories: mTV series 　　cMT-SVR series 　　If cMT-SVR ...

30. Button control indicator (same address) Set the multi-state transfer switch element/bit state transfer switch element and the multi-state indicator element/bit status indicator element to the same address, click the multi-state transfer switch element/bit state transfer switch element, and the corresponding indicator ...

Some tips for using the contact screen If you change the display resolution or display form of the contact screen from scratch when you operate the capacitive contact screen in the middle of the operation, or you may adjust the refresh rate of the contact screen controller by yourself, and you feel that the cursor and the contact point do not correspond, you must ...

Virtual serial port configuration process: 1. Open the virtual serial port configuration software and create two pairs of serial ports; 2. The circle is the physical serial port in the computer, and the virtual serial port in the box; 3. Two groups have been added, and friends who want to add port tests can do so in the window on the right.

1. The memory address is different. The memory address of the PW touch screen uses the local hold register, while the memory address of the RW uses the hold register index to send RWI. 2. The address range is different. The address range of the LW of the touch screen is 0 to 524287, while the address range of the RW is 0 to .

1.1 How to delete the job button on the taskbar of the touch screen? Set "Modify/Set System Parameters/General/Job Buttons/Features" to "Closed". 1.2 What does RS485 Default/RS485 2W/RS485 4W Separation mean in the communication port type? r ...

Due to technical limitations and poor environmental adaptability, especially the surface acoustic wave screen, the screen will not be able to be used normally due to water droplets, dust and other pollution, so the Weilun touch screen also needs regular maintenance like ordinary machines. And because the Weilun touch screen is a variety of electrical equipment...

4. Use Fault 4.1 What should I do if the newly purchased touch screen downloads the programmed program and it cannot be touched or the touch freezes? First of all, hit the No. 2 DIP switch on the back of the screen to the direction of on, and then power on to see the copyright of the last line of the screen.

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

1. The motherboard cannot recognize/display the peripheral devices. 2. The peripherals will stop working for a few seconds or more. 3. A slow boot may indicate that your motherboard is broken, although it could also be other components. 4. The touch screen does not recognize the flash drive, or ...

18. Macro calculation: The values to be calculated are read, and then the data is calculated and written to LW0. 19. According to the different selections of the project menu, two different direct windows will pop up with one button: Macro commands are triggered by a button to read the ...

The five-wire resistive touch screen and the four-wire resistive touch screen both adopt the principle of analog resistance, and their conventional fault characteristics are exactly the same as those of the four-wire resistor. If you are using a five-wire resistive touch screen, when there is an installation and maintenance problem, please determine and solve the problem in the following order. ...

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...

Right-double-click the parameter settings button. Specific steps: 1. Create a new screen, and then make a keyboard, and the OK button is [Screen Jump Control] 2. Double-click the [Parameter Setting] button and select [Properties]. 3. Click [Security], and then ...

Why can't the infrared touch all-in-one machine be calibrated? 1. It is possible that the touch screen control card receives the operation signal before the host starts to load the touch screen driver, please power off and restart the computer and recalibrate. 2. It is possible that the sound wave screen is used for a period of time, ...

Open the Veriton touch screen programming software, select [Common] in the main interface and open it In the Common drop-down menu, select System Parameters and click Open. Then select [HMI Attributes] in the pop-up system parameter setting menu and click OK. ...

(1) FILM - that is, the film used for touch, the base material is PET. When touched, the ITO of the upper and lower layers is brought into contact by deforming the film, resulting in different "resistance values" in the X and Y axes (similar to the principle of moving rheostats). Depending on the requirements of use, the table of FILM ...

When the HMI communication failure is caused by on-site interference, the following methods can be used to troubleshoot the fault: The communication line adopts shielded twisted pair cable, and the shielding layer needs to be grounded at one end, that is, only one end of the PLC and the touch screen can connect the shielding layer to the ground horn (it is recommended to connect it to the HMI end of the touch screen) ...

Weiluntong contact screen repair 　　The first step in troubleshooting a touchscreen system is to determine if the problem is related to the display, software, or hardware: Don't confuse the visibility issue with the contact screen issue, the two are unrelated. Software problems are caused by fundamental hardware functions ...