Square type High power reflective type M8 connector type 500mm
specification
type | Background tuning: Distance setting | appearance | rectangle | output | PNP | Connection patterns | M8 connector (3-pin) | Detection distance | 35 to 500 mm (465 to 0)*3 | Standard detection segment difference | 35 to 180 mm: 9 mm | 180 to 300 mm: 25 mm | 300 to 400 mm: 40 mm | 400 to 500 mm: 50 mm | Display resolution | 1 to 5 (1 to 5 mm) | Spot diameter | approx. ø3 mm | Response time | 1.5ms/10ms/50ms switching | light source | type | Red laser (660 nm) | Laser classification | Class 2 Laser Products (IEC60825-1) | Class II Laser Products (FDA (CDRH) Part1040.10) | function | Light | 3-digit 7-segment display (white), output indicator (yellow), | DATUM indicator (orange), 1 spot indicator (green) | timer | OFF/ON- Delay/OFF- Delay/One Touch | Electrical Specifications | Supply voltage | 10-30 VDC, including fluctuation 10% (p-p), Class 2 or LPS | Power consumption | 450 mW or less (18 mA at 24 V, 34 mA at 12 V) | Control the output | PNP open collector | The applied voltage is less than 30 VDC, the control current is less than 100 mA, | Below 1.2 V at 10 mA and 2 V at 10 to 100 mA | Protection circuits | Power supply reverse polarity protection, output overcurrent protection, output surge protection, output reverse polarity protection | Output actions | The switching method of ON when entering light / ON when shading | Environmental resistance | Enclosure protection grade | IP68 (IEC60529)、IP69K (DIN40050-9)、ECOLAB*4、Diversey*4 | Insulation resistance | 20 MΩ or more (500 VDC) | Ambient lighting | At 250 mm: | Incandescent lamps: 10,000 lux or less | Daylight: 20,000 lux or less*5 | At 500 mm: | Incandescent lamps: 2,000 lux or less | Daylight: 4,000 lux or less*5 | Ambient temperature | -10 to +50 °C (no freezing) | Store at ambient temperature | -25 to +75 °C (no freezing) | relative humidity | 35 to 85 % RH (non-condensing) | Withstand voltage | 1,000 VAC、50/60 Hz、1 min | Earthquake resistance | 10 to 55 Hz, double amplitude 1.5 mm, 2 hours each in X, Y, Z directions | Impact resistance | 6 times each in the 1,000 m/s2, X, Y, Z directions | Material | Housing: SUS316L, Display: PES, Lens Cap: PMMA with anti-scratch coating, Gasket / Connector Ring: FKM | annex | Instruction Manual, FDA Warning/Certification/Identification Label, Warning/Instruction Label | weight | Approx. 55 g | *1 IO-Link: Specification v.1.1/COM2 (38.4 kbps) is supported. The configuration software can be downloaded from the KEYENCE website.
If you are using the file in an environment where you cannot download files via the Internet, please contact the nearest sales office.
*2 The M8 connector (3-pin) type does not have an external input function.
*3 Reference display value related to detection distance. If the set value is tuned, the value will be displaced. Also, when "-99" is exceeded, the display will turn to "-FF".
*4 We have tested the durability of each company's cleaning agents.
*5 Response time is 10 ms
This article introduces the KEYENCE/KEYENCE amplifier built-in CMOS laser sensor LR-Z series LR-ZH500C3P products, if you are interested in KEYENCE/KEYENCE products, please also contact our customer service, we look forward to your call, hope our technology and service can bring you a better experience.
The company has been customer-centric, the concept of creating value for customers, winning the market with quality and service, and sincerely hopes to cooperate with all sectors of society to create success, create brilliance together, and work together to create a better tomorrow! In line with the concept of credibility and service-oriented, the company warmly welcomes new and old customers to inquire, visit and negotiate business
|
More on that
|
KEYENCE/KEYENCE Fiber Optic Components Visual Receiver FU-R77TZ
Type: Optical fiber with indicator type (visual receiver) Threaded hexagonal fiber
Optical axis diameter Beam: ø 1 mm Reception: ø 3.2 mm
Size M4
The length of the fiber optic unit is 2 m and can be cut freely
Diameter of the fiber optic unit ø 2.2
Shape: Hexagonal
Small...
|
|
KEYENCE/KEYENCE Laser Sensor LR-X Series M8 OP-88507 Connector Type Cable High elasticity 10 m
M8 connector type cable with high elasticity of 10 m
Type: High elasticity
Sensor side: M8 4pin straight
Cable termination: Loose wires
Length: 10 m
Material: Cable part :P VC connector part: Brass nickel plated
Weight: approx. 370 g
This article describes ...
|
|
KEYENCE/KEYENCE Laser Sensor LR-TB2000/5000 Reflectivity
Summary: The LR-T series offers a variety of innovative features to detect previously thought undetectable targets. These features allow the user to tailor the sensor to the specific application, ensuring excellent detection performance. The LR-T Series provides stable detection from a position that does not obstruct the operator, eliminating the need for manipulation.
|
|
KEYENCE/KEYENCE Amplifier Built-in CMOS Laser Sensor LR-Z Series OP-87619
Connector cable M8L word 2m resistant
Type: Connector cable Chemical resistant
End Shape: M8 L-Shaped - Loose Wire
Length: 2 m
Material: Cable: PVC, Nut: SUS316L
Weight: approx. 70 g
This article introduces the KEYENCE/KEYENCE amplifier built-in CM ...
|
|
KEYENCE/KEYENCE Multi-Point Laser Sensor OP-87458
Ethernet cable (M12 4pin-RJ-45) NFPA79 standard standard cable 5 m
Type: NFPA79 standard Ethernet cable
End shape: M12 4pin-RJ-45
Length: 5 m
This article introduces the KEYENCE/KEYENCE multi-point laser sensor OP-87458 ...
|
|
KEYENCE/KEYENCE Digital Ultrasonic Sensors FW Series UL Approved
Introduction: KEYENCE/KEYENCE Digital Ultrasonic Sensor FW Series uses a new algorithm A.W.S. (Active Wave Stabilizer) to achieve stable inspection without the influence of workpiece differences and ambient light. At the same time, this product has obtained CE mark certification and UL certification, which can be assured to make ...
|
|
KEYENCE/KEYENCE Multi-Point Laser Sensor IX-360
Sensing head 360 mm
specification
*1 X: Laser long dimension direction, Y : Laser short dimension direction
*2 When facing each other at the base distance. Scanning mode: When measuring with a height tool, a small measuring point, and no position correction.
*3 When facing at the base distance. ...
|
|
KEYENCE/KEYENCE Display Panel LK-HD500
Display panel LK-HD500
specification
Type: Display unit
Supported models: LK-G5000, LK-G5000P
display
Minimum display module: 0.001 μm
Display range: ±999.999 μm to ±9999.99 mm (selectable in 7 stages)
Show week ...
|
|
KEYENCE/KEYENCE Digital Infrared Temperature Sensor FT Series Range 3000mm
Introduction: KEYENCE/KEYENCE Digital Infrared Temperature Sensor FT Series Depending on the application, it is possible to measure the target and the sensor at a certain distance, from small light spots to long-distance use, and various types of sensor heads are available to cope with various installation environments.
Features:
...
|
|
KEYENCE/KEYENCE Multi-Point Laser Sensor OP-87953
LAN cable (RJ-45-RJ-45) 10 m
Type: LAN cable
Length: 10 m
Weight: approx. 600 g
This article introduces the KEYENCE/KEYENCE Multi-Point Laser Sensor OP-87953 product, if you are interested in KEYENCE/KEYENCE products, please also contact our customers.
|
|
KEYENCE/KEYENCE Laser Sensor LR-X Series Adjustable Bracket A OP-88501
KEYENCE/KEYENCE Laser Sensor LR-X Series Adjustable Bracket A OP-88501
Shape: Adjustable Bracket A (Sensor Probe Fixing Screw × 2 Accessories)
Material: SUS316L etc
Weight: approx. 15 g
This article introduces the KEYENCE/KEYENCE laser ...
|
|
KEYENCE/KEYENCE CMOS Laser Displacement Sensor Controller LK-H027K
Sensor head wide type LK-H027K
specification
This article introduces KEYENCE/KEYENCE CMOS Laser Displacement Sensor Controller LK-H027K products, if you are interested in KEYENCE/KEYENCE products, please also contact our customer service, we look forward to your call, hope our ...
|
|
KEYENCE/KEYENCE Laser Sensor LR-X Series LR-XN12P
KEYENCE/KEYENCE Laser Sensor Amplifier Split Amplifier Cable Type Expansion Unit PNP LR-XN12P
*1 When 500 μs is selected, the following limits are specified.
· Tuning is limited to 2-point tuning.
· The detection range shield is set during tuning. (The screen is not supported...)
|
|
KEYENCE/KEYENCE CMOS Laser Displacement Sensor IL-1050
keyence KEYENCE CMOS Laser Displacement Sensor Amplifier Unit DIN Rail Mount Type IL-1050
Power supply voltage: Supplied by the main module*3
Power consumption: 2000 mW or less (67 mA or less at 30 V)
Pollution level: 2
Ambient temperature: -10 to +50 °C ( ...
|
|
KEYENCE/KEYENCE CMOS Laser Displacement Sensor Controller LK-H022
Sensor head Spot type laser class 2 LK-H022
specification
This article introduces KEYENCE/KEYENCE CMOS Laser Displacement Sensor Controller LK-H022 products, if you are interested in KEYENCE/KEYENCE products, please also contact our customer service, we look forward to your call ...
|
|
KEYENCE/KEYENCE Laser Sensor LR-X Series LR-X250C (Detection Distance: 250mm)
Laser sensor standard type M8 connector type (detection distance 250mm)
*1 The cable length of the M8 connector type is 30 m or less. When connecting IO-Link, keep it to less than 20 m.
*2 When 500 μs is selected, the following limits are specified.
· Tuning is limited to 2 points ...
|
|
KEYENCE/KEYENCE Flow Sensor FD-M Series has a pressure resistance of 2.0 MPa
Introduction: KEYENCE/KEYENCE Flow Sensor FD-M Series The FD-M Series uses Faraday's law to determine the flow rate of conductive liquids. A typical electromagnetic flow sensor uses electrodes that are in contact with the liquid inside the test tube to detect the electromotive force of the liquid. The FD-M series is determined by electrostatic capacitance ...
|
|
KEYENCE/KEYENCE Ultra-Compact Amplifier Built-in Photoelectric Sensor PR-M/F Series PR-FB30N3
KEYENCE/KEYENCE Photoelectric Sensor with Built-in Ultra-Small Amplifier PR-M/F Series Squared Reflective Type (Background Suppression) Cable Type 30mm PR-FB30N3
specification
In this article, we introduce the KEYENCE/KEYENCE ultra-compact amplifier built-in photoelectric sensor PR-M/F Series PR-FB30N ...
|
|
KEYENCE/KEYENCE Ultra-Small Amplifier Built-in Photoelectric Sensor PR-M/F Series PR-MB30CN
Mini slim BGS reflective M8 connector type 30mm PR-MB30CN
specification
This article introduces the KEYENCE/KEYENCE ultra-miniature amplifier built-in photoelectric sensor PR-M/F Series PR-MB30CN products, if you are interested in KEYENCE/KEYENCE products, please also contact our customers.
|
|
KEYENCE/KEYENCE Amplifier Built-in TOF Laser Sensor LR-T Series LLR-TB5000
Detection distance: 5m Cable type Laser classification 2
*1 Can be displayed from 50 to 5200.
*2 The classification by the FDA (CDRH) is based on IEC60825-1 and is implemented in accordance with the requirements of Laser Notice No. 50.
*3 I/O can be selected from the following combinations.
・Control ...
|
|