Mitsubishi inverter E6 and E7 are faulty

There is a capacitance between the wires of the cable, and a qualified cable can limit this capacitance to a certain size. It is a qualified cable, when the cable length exceeds a certain length, the capacitance value between the lines will also exceed the required value, when the cable is used for PLC input, the capacitance between the lines will be ...

Planning PLC control system control requirements for electroplating production line: 1) SQ1-SQ4 is the driving advance and retreat limit switch, and SQ5-SQ6 is the upper and lower limit switches. 2) The workpiece is lifted to SQ5 to stop, and the car is driven to SQ1 to stop.

Mitsubishi inverter we have to maintain the inverter module frequently, to regularly check the Mitsubishi inverter module, especially the maintenance of the cooling fan, due to the high power of the cooling fan, high speed, in the dusty working environment, simply lead to the radiator exhaust hole blockage, so that the internal electric ...

Introduction to Mitsubishi PLC directives such as negation, air operation and END The INV (Inverse) command is represented by a short 45° slash at the top of the ladder diagram, which negates the result of the operation before the execution of the instruction, and the result of the operation is 0 ...

When evaluating which process is suitable for which approach in the production environment, consider the problem you want to solve and consider all the costs that the robot can save: reduce waste, improve efficiency, improve productivity, improve safety, or reduce labor costs. These costs ...

Servo drive system requirements 1. Wide speed regulation 2. High positioning accuracy 3. Satisfactory transmission rigidity and high speed stability 4. Fast response, no overshoot In order to ensure productivity and processing quality, in addition to the requirement of high positioning accuracy ...

The origin orientation is incorrect, and the encoder debugs/zeros the bit Replacement of bearings, wear of bearing grooves, cracking of the rotor, cracking of the shaft Gear groove wear The magnet bursts steel, the magnet falls, gets stuck and doesn't move Encoder wear, code/glass disc wear and crack ...

1. The switching signal of PLC controls the inverter The output point and COM point of the PLC (MR type or MT type) are directly connected to the STF (forward engine), RH (high speed), RM (medium speed), RL (low speed), and input SG ports of the inverter. The PLC can be programmed to control the inverter's start, ...

The 30MA-eX-F40 fiber laser flexible active loading and unloading system was jointly developed by Mitsubishi Electric Corporation's Laser Division and Mitsubishi Electric Electromechanical Technology Co., Ltd. ...

In the MR Configurator2 servo commissioning software, Mitsubishi has developed a "one-button adjustment" function to solve the problem of rigid noise of servo motors, as follows: 1. Set PA08 to 0003 and adjust the gain to ...

Mitsubishi servo motor system series: MR-J2S series, MR-J3 series, MR-ES series, MR-E series. Mitsubishi servo motor MR-J2S series 1. The product also has RS-232 and RS-422 serial communication functions, which can be used by a personal computer equipped with servo setting software.

Servo motors are generally operated by three circuits. To put it bluntly, the three circuits are three closed-loop control negative feedback PID control systems. The first innermost PID loop is the current loop, which is implemented completely inside the servo controller. Exercise...

A PLC network consists of multiple subnets. The communication process of each subnet is determined by the communication protocol. The communication method is the core content of the communication protocol. The means of communication include visit control and data transmission. What are the three common communication methods of PLC? ...

1. No-load energizing test of Mitsubishi inverter. 1. Ground the ground terminal of the Mitsubishi inverter. 2 Connect the power input terminal of the Mitsubishi inverter to the power supply through the leakage maintenance switch. 3 Check whether the factory display window of Mitsubishi inverter is normal, if it is not correct.

1. What is suspension? The so-called suspension refers to the fact that in the process of sequentially performing the program scanning, when there is a request to respond immediately, the scanning work performed at that time is immediately suspended, and the service work specified in the request is performed first. When the service job is complete, go back to ...

1. The output side of the inverter is short-circuited, such as the connection line between the output end and the motor, or the short circuit inside the motor, etc.; 2. The inverter itself is not working properly, such as the two inverter equipment of the same bridge arm in the inverter bridge are constantly alternating in the working process ...

1) LD (take instruction) A command to connect a normally open contact with the left bus, and every logic line that starts with a normally open contact is used with this instruction; 2) LDI (Reverse Instruction) A normally closed contact is connected to the left bus to the instruction, each ...

1. The workbench runs in the direction of the decrease of the value of the current value register (generally M8342=OFF in the opposite direction), and when it encounters the near-point signal, it becomes a creeping speed, and the zero-point signal after leaving the near-point signal arrives with a delay of 1ms, and the pulse output is immediately aborted. ...

The programming philosophy is different Mitsubishi PLC is a Japanese brand, programming is intuitive and easy to understand, and it will be easier to learn, while Siemens PLC is a Germany brand, the instructions are more general, it is more difficult to learn, but there are fewer instructions, and Mitsubishi has more instructions, so learn Mitsubishi and learn Siemens' week ...

There are several ways to classify frequency converters: According to the classification of the main circuit operation method, it can be divided into voltage-type inverter and current-type inverter; According to the classification of switching methods, it can be divided into PAM control inverter, PWM control inverter and high carrier frequency PWM control inverter; In accordance with the ...