Estun servo motor - how to choose a servo motor?

Speed regulation of DC motors Constant power weak magnetic upward speed regulation, the magnetic field governor can be adjusted until the speed reaches the required value, but shall not exceed the maximum speed allowed by the technical conditions. Constant torque loads can be slowed down by step-down or armature string resistors. Downtime of the DC motor ...

(1) The motor heat dissipation system is faulty The temperature of the motor rises due to the heat generated by the motor not being dissipated quickly. At this time, the main solution is to check whether the cooling fan of the motor is operating normally and whether the direction of rotation of the fan is correct. The surface of the motor is ...

1. Position proportional gain Set the proportional gain of the position ring adjuster; The higher the set value, the higher the gain, the greater the stiffness, and the smaller the position lag under the same frequency command pulse. However, too large a value may cause oscillation or overshoot; The parameter values are determined by the specific servo system type ...

1. Motor encoder alarm 1. The cause of the failure (1) Wiring fault; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment. 2. Fault cleaning (1) Check the wiring and sweep away the fault ...

1. Torque control: The torque control mode is to set the size of the output torque of the motor shaft through the input of the external analog quantity or the assignment of the direct address, which is specifically manifested as if 10V corresponds to 5Nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5Nm: if the motor shaft ...

What points do you need to pay attention to when using welding robots? 1. It is necessary to teach the robot before active welding, and it is necessary for the operator to teach the track of the robot welding gun and set the welding conditions. Because it is necessary to teach, the robot is not oriented to many classes ...

Possibility of failure 1. Communication line related issues; 2. Drive parameter problems (PN703, PN704); 3. Problems with the setting of communication parameters of the main station; 4. External interference; 5. The drive is damaged. Solution: 1. Ensure that the communication line is made correctly.

1. Positional proportional gain Sets the proportional gain of the position ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the position lag under the same frequency command pulse. However, too large a value may cause oscillations or overshoots. The parameter values are determined by the specific servo model ...

1. Fault phenomenon: The uneven distribution of the magnetic field of the ions, the unbalanced three-phase current aggravates the vibration and noise of the motor during operation, and the motor cannot be started when it is serious, and a large short-circuit current is generated in the short-circuit coil, which causes the coil to heat up rapidly and burn out. 2. Causes: ...

What are the main differences between the two? 1. The way of control is different Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to a step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. Work ...

First, the control accuracy is different The step angle of the two-phase hybrid stepper motor is generally 3.6 ° and 1.8 °, and the step angle of the five-phase hybrid stepper motor is generally 0.72 ° and 0.36 °. There are also some high-performance stepper motors with smaller step angles. Such as Sitong company produced a kind of wire for slow wire ...

21. How to choose whether to use planetary reducer or spur gear reducer? Planetary reducer is generally used when high torque is required in a limited space, that is, small volume and large torque, and its reliability and life are better than that of spur gear reducer. Spur gear reducers are used for lower ...

Servo drive is a kind of controller used to control servo motor, its role is similar to the inverter to ordinary AC motor, as a precision equipment, it will inevitably have some faults in the process of use, common faults and maintenance methods are as follows: 1. When the motor rotates, the LED light ...

The following preparations need to be made for starting when the motor is put into operation after installation or before it is put back into operation after being shelved for a long time: (1) Use compressed air to blow off the dust attached to the inside of the motor, and remove the wrapping paper at the windshield for new motors. Check whether the bearing grease is clean and suitable.

On September 25, 2020, a group of 20 people from the Industry and Information Think Tank Alliance, led by Comrade Fan Bin, Deputy Director of the Department of Political and Legal Affairs of the Ministry of Industry and Information Technology, visited Estun Company for research. Dr. Wang Jiegao, President of Estun Automated Robot Research Institute, and Ms. Yuan Qin, Deputy General Manager, accompanied the visit and investigation. The experts visited ...

1. Applicable welding methods and cutting methods: Generally, arc welding robots are only suitable for MIG/MAG welding, and there is no interference of high-frequency arc striking on the control and drive system of the robot. Whether it can be used for tungsten argon arc welding depends on whether the robot has a special anti-interference method.

1. Fault phenomenon of servo motor encoder Due to improper loading and unloading, the encoder code disc is cracked and worn 2. Reasons for damage to servo motor encoders 1. Due to the abnormal external force on the motor shaft, the encoder code disc is displaced with the shaft, and the light receiving mirror is rubbed and grinded.

The servo control system is an operating system that can automatically control the mechanical movement of the test device according to the predetermined requirements. There are many classification methods for servo systems, and there are three common classification methods: 1. Classification according to the characteristics of the controlled parameters. 2. According to the type of drive element ...

A servo control system is a feedback control system that is used to accurately follow or reproduce a process. In many cases, the servo system refers specifically to the feedback control system in which the controlled quantity (the output of the system) is the mechanical displacement or displacement velocity and acceleration, and its function is to make the mechanical displacement of the output (or ...

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...