The correct use of thermocouples can not only accurately obtain the temperature value to ensure that the product is qualified, but also save the data consumption of thermocouples, which can not only save money but also ensure product quality. Incorrect devices, thermal conductivity and moment lag are the first errors in the use of thermocouples.
1. Thermal resistance error
At high temperatures, if there is a layer of coal ash on the maintenance pipe and dust adheres to it, the thermal resistance is added to hinder the conduction of heat, and the temperature indication is lower than the true value of the measured temperature. Therefore, the outside of the thermocouple maintenance tube should be kept clean to minimize errors.
2. Errors introduced due to deterioration of insulation
If the thermocouple is insulated, the maintenance pipe and the cable plate are too dirty or salt, resulting in poor insulation between the thermoelectric dipole and the furnace wall, which is more serious at high temperatures, which will not only cause the loss of thermoelectric potential but also introduce interference, and the resulting errors can sometimes reach hundreds of degrees
3. Errors in the introduction of thermal inertia
Because the thermal inertness of the thermocouple causes the indicated value of the surface to lag behind the change in the measured temperature, this effect is particularly prominent when making rapid measurements. Therefore, thermocouples with thinner thermoelectrodes and smaller diameter maintenance tubes should be used as much as possible. If the temperature measurement environment permits, the maintenance tube can even be removed. Because of the measurement hysteresis, the amplitude of the temperature fluctuation detected by the thermocouple is smaller than that of the furnace temperature fluctuation. The greater the measurement hysteresis, the smaller the amplitude of the thermocouple shaking and the greater the difference from the actual furnace temperature. When a thermocouple with a large time constant is used to measure or control the temperature, the temperature of the apparent appearance fluctuates very little, but the actual furnace temperature fluctuates greatly. In order to measure the temperature accurately, thermocouples with small time constants should be selected. The moment constant is inversely proportional to the heat transfer coefficient, and is directly proportional to the diameter of the thermocouple hot end, the density of the data and the specific heat. In application, it is common to use materials with good thermal conductivity, thin pipe walls and small inner diameter maintenance sleeves. In more precise temperature measurement, bare wire thermocouples without maintenance sleeves are used, but the thermocouples are easy to be damaged and should be calibrated and replaced in time.
4. Errors caused by improper introduction of devices
In other words, the thermocouple should not be installed too close to the door and the heating, and the penetration depth should be at least 8-10 times the diameter of the maintenance tube; The interval between the thermocouple maintenance sleeve and the wall is not filled with thermal insulation substances, resulting in heat overflow or cold air intrusion in the furnace, so the open space between the thermocouple maintenance pipe and the furnace wall hole is blocked by thermal insulation materials such as refractory mud or asbestos rope to avoid the convection of cold and hot air and affect the accuracy of temperature measurement; The cold end of the thermocouple is too close to the furnace body to exceed 100°C; The device of the thermocouple should avoid strong magnetic fields and strong electric fields as much as possible, so the thermocouple and the power cable should not be installed in the same conduit to avoid the introduction of interference and errors; When measuring the temperature of the gas in the tube with a thermocouple, it is necessary to make the thermocouple device in the direction of the flow velocity and fully contact with the gas.
|
More on that
|
Turbine fixed ball valve standard execution suppression - Wuzhong instrument
The process of shell experiments and seal experiments done by turbine fixed ball valves in some artificial environments is as follows.
Double blocking and discharge function of turbine fixed ball valve: the turbine ball valve is fixed by using tension spring preload float valve seat, when the valve is in two different states, full open and fully closed, the fluid is ...
|
|
The selection of Wuzhong instrument control valve
In the process control system, the control valve accepts the control signal of the control instrument, directly touches with the fluid, adjusts the flow of the fluid, and controls the flow, pressure, temperature, liquid level and other elements in the system, so it understands the fundamental structure and characteristics of the control valve, and selects it correctly according to the process conditions of the system. ...
|
|
How to use thermocouples in Wuzhong meters
The correct use of thermocouples can not only accurately obtain the temperature value and ensure that the product is qualified, but also save the data consumption of thermocouples, which can not only save money but also ensure product quality. Incorrect installations, errors such as thermal conductivity and time lag are the first errors in the use of thermocouples.
|
|
Maintenance method of safety valve - Wuzhong instrument
1. The safety valve should have the equipment to prevent the hammer from moving by itself and the guide frame to limit the lever from deviating, and the spring-type safety valve should have the equipment to raise the handle and prevent the adjustment screws from being twisted at will.
2. It should be installed straight in the pot merchant, the container ...
|
|
Instrument maintenance - Wuzhong instrument
The normal operation of the appearance is inseparable from the protection of the site, especially some important process links, once there is a leak, it will greatly affect the quality of the product, resulting in heavy losses.
First of all, on important tanks in general ...
|
|
The structure of the pressure reducing valve - Wuzhong instrument
Load the organization
The role of the loading tissue is to apply a downward loading force from the top of the pressure reducing valve. The loading structure of the FITOK pressure reducing valve is mainly the loading of tension springs. Tension spring loading has the advantage of reliability and low cost, and is the most versatile loading device in pressure reducing valves.
|
|
Product features of eccentric hemispherical valve - Wuzhong instrument
(1) The sealing pair is spherical, disc eccentricity rotation planning
The valve sealing pair is spherical planning, and the sealing effect is good. Together with the disc rotation center is planned to have a bias with the center of the valve seat, so the valve disc and the valve seat form a bias cam wedge sealing effect when closed, the valve ...
|
|
Wuzhong instrument control valve components
1. Valve body assembly
The valve body assembly shall have the following elements: structural type, nominal diameter, nominal pressure, connection type with pipeline, applicable temperature scale, raw materials of valve body and internals, valve seat diameter or rated flow coefficient, flow characteristics, valve seat leakage grade, etc.
...
|
|
Wuzhong instrument-control valve knowledge
The actuator of the control valve has pneumatic type, electric type and electro-hydraulic linkage type, and the pneumatic equipment is divided into barrier type and cylinder type. Depending on the action when the operating signal and the drive source disappear, the actuator has a forward type, a reverse type, a non-directional type, and a persistent type. The positive type is used in the operation signal and drive ...
|
|
Pneumatic control valve failure and its causes - Wuzhong instrument
(1) The conditioning valve does not operate. The symptoms and causes are as follows:
1. No signal, no air source. (1) The air source is not opened, (2) because the water contained in the air source freezes in winter, resulting in the blockage of the air duct or the blockage of the filter and pressure reducing valve, (3) the compressor is faulty; (4) Leakage of air source main pipe.
2． ...
|
|
Non-technical failure analysis of hard seal ball valve - Wuzhong instrument
From the perspective of product application, hard seal ball valve defects can be roughly divided into the following two categories: non-technical faults and skill defects. The following text mainly introduces the analysis and solution of non-technical problems of hard seal ball valves;
...
|
|
How to maintain the valve in the operation of Wuzhong instrument
For valves in operation, all kinds of valves should be complete and defective. For example, the bolts on the flange and bracket should not be short, and the threads should be free of defects, and no loosening is allowed.
The fastening nut on the handwheel, if found to be loose, should be ...
|
|
Detection instrument (component) and control valve selection principle - Wuzhong instrument
1. High-precision operation, can complete rapid palletizing and destacking operations.
(1). The conditions of the process
Factors such as temperature, pressure, flow, viscosity, corrosiveness, toxicity, pulsation and other factors in the process determine the appearance of the ...
|
|
The torque of the electric actuator of the valve is faulty
1. Torque maintenance refusal
To measure the output torque of the electric actuator, there are mainly mechanical maintenance switches, motor current and voltage power measurement and calculation torque, and sensor-type maintenance devices: mechanical torque maintenance switches were used more before 2000 and were classified as a transitional product.
|
|
Key points of classification and selection of cryogenic valves - Wuzhong instrument
Cryogenic valves are mainly used in ethylene, liquefied natural gas units, air separation equipment, petrochemical tail gas separation equipment, liquid oxygen, liquid nitrogen, liquid argon, carbon dioxide cryogenic storage tanks and tankers, pressure swing adsorption oxygen production devices, etc., the main varieties are cryogenic ball valves, cryogenic globe valves, etc.
...
|
|
Wuzhong instrument valve selection precautions
Valve application requirements
(1) General gate valves, ball valves, and globe valves are prohibited from dispatching according to their structural characteristics. However, in process design, it is widely used for mediation. Because of the scheduling application, the valve seal has been in a throttling state for a long time, and the impurities in the oil have washed the seal, endangering the seal.
|
|
Precautions for the installation and use of electric control valve - Wuzhong instrument
1. The hydraulic power in the hydraulic ball valve should refer to the opening mode of the valve as hydraulic, which refers to the valve opening device. The latter ball valve refers to the valve type as a valve type and a shut-off valve class.
Two: Type Q61N can explain Q as ...
|
|
The relationship between the valve diameter and the flow rate of the medium
The flow rate and velocity of the valve mainly depend on the diameter of the valve, and are also related to the resistance of the structure of the valve to the medium, and at the same time have an intrinsic relationship with the pressure, temperature and concentration of the medium of the valve.
Two...
|
|
Introduction to valve corrosion and solutions - Wuzhong instrument
1. Corrosion of valves is usually understood as the damage to the metal materials of valves under chemical or electrochemical environmental effects. Because the corrosion phenomenon occurs in the spontaneous interaction between the metal and the surrounding environment, therefore, how to block the metal from the surrounding environment or more use of non-...
|
|
Wireless remote valve control system - Wuzhong instrument
1. System overview
The valve automatic control system controls the solenoid valve equipment placed in the field by announcing the instructions of the control service center in a wireless way, and then realizes the opening and closing of the solenoid valve, and the opening and closing status of the valve, the operation status, whether the equipment is online, historical data inquiry, etc.
|
|
Contact
working hours
