Steps on how Hollysys DCS works on a computer

1. Power off 2. Cleaning the ash can not only clean the surface, but also clean the internal card key of the controller 3. If there is a supporting UPS, open the UPS and clean the ashes 4. After cleaning the ash, check whether the card and relay are loose, and tighten them if they are loose 5. The relays with frequent actions should be cleaned regularly.

1、-10—10V。 When the voltage of -10V-10V is converted to F448-0BB8Hex (-3000-3000) at 6000 resolution; At 12000 resolution, it is converted to E890—1770Hex (-6000—6000). 2、0—10V。 At a voltage of 0-10V, at a resolution of 12000 ...

1. Configuration of the system and controller The configuration of systems and controllers focuses on reliability and load factor (including redundancy). The communication load rate must be controlled within a reasonable range, and the load rate of the controller must be balanced as much as possible to avoid the occurrence of "high load" problems. 2 ...

01. Power supply The DCS power supply system is mostly a "dual backup hot redundant power supply", and the prevention and control of power failures is mainly reflected in the inspection and daily maintenance. Generally speaking, as long as the unit is normal ...

1. Budget for input and output (I/O) points When budgeting I/O points, the appropriate margin should be considered, usually based on the calculated number of input and output points, and then add 10%-20% of the expandable, and after the margin, it will be used as the budget data of input and output points. When ordering in practice, it is also necessary to rely on the manufacturer's ...

1. Circuit isolation The isolation of analog circuits is more complex, mainly depends on the accuracy requirements of the transmission channel, the higher the accuracy requirements, the higher the cost of the channel; However, when the performance requirements rise to the main contradiction, the isolation components should be selected based on performance, and the ...

The control of pulse amount is mostly used for angle control, distance control, position control and so on of stepper motor and servo motor. The following is an example of a stepper motor to illustrate each control mode. 1. Angle control of stepper motor. First of all, it is necessary to clarify the number of subdivisions of the stepper motor, and then determine the stepper ...

1. The switching signal of PLC controls the inverter The output point and COM point of the PLC (MR type or MT type) are directly connected to the STF (forward start), RH (high speed), RM (medium speed), RL (low speed), and SG input ports of the inverter. PLC can control the frequency conversion through the program ...

(1) There are three forms of programmable controller: relay output, thyristor output, and transistor output. (2) The wiring of the output terminal is divided into independent output and common output. When the output relay or thyristor of the PLC is activated, the two output terminals of the same number are turned on. In different groups, you can ...

(1) The ambient temperature exceeds the range of 0-50 °C; (2) The relative humidity exceeds 85% or there is dew condensation (caused by sudden temperature changes or other factors); (3) direct sunlight; (4) There are corrosive and flammable gases, such as hydrogen chloride, ...

1. PLC programmable logic controller (programmable controller). 2. DCS system pays more attention to the field of process control. Such as chemical, smelting, pharmaceutical, etc. It mainly monitors and controls some field parameters, while PLC focuses on logic control. machining). Of course, the PLC's ...

Whether it is a new unit or an upgraded DCS, the equipment of the system and controller should focus on the reliability and load factor (including redundancy) objectives. The load rate planning of the communication bus must be controlled within a reasonable range, and the load rate of the controller should be balanced as much as possible.

(1) Development in the direction of integration: the development of standardized data communication links and communication networks, and the formation of a large system of various single (multi) loop regulators, PLCs, industrial PCs, NCs and other industrial control equipment to meet the requirements of factory automation and adapt to the general trend of openness. (2) To the intelligent ...

1. Check the circuit according to the drawing (without power transmission) The drawings of the general PLC system include two parts: the drawings in the cabinet and the drawings outside the cabinet; The drawing in the cabinet refers to the wiring diagram inside the cabinet; The out-of-cabinet drawings are the wiring diagrams of all electrical cabinets that are connected out. This part needs to be checked for; 1. Drawings ...

The steps of DCS system troubleshooting include: (1) Check the fault caused by improper use. Common types of operational faults include operator errors, terminal wiring faults, module installation faults, and power supply failures. (2) Troubleshoot the improper operation of the DCS system ...

When the PLC understands the interrupt function, it needs to understand the PLC's operating cycle or scan cycle. It is necessary to talk about the process of PLC sequential control loop execution, which is a prerequisite for understanding interruptions and must be mastered. It is divided into three parts, input processing, program processing, and output processing. 1、 ...

(1) High reliability DCS is designed to be fault-tolerant, so that when a computer fails, it does not cause the system to lose other functions. In addition, because the tasks undertaken by the individual computers in the system are relatively simple, it is possible to adopt a specific structure and ...

1. Preliminary preparations Engineering configuration is operated at the engineer station, and before engineering configuration, it is necessary to have the necessary tools and information, specifically: Tools: refers to the hardware environment and software environment used in engineering configuration, usually refers to the ...

1. Peripheral circuit component failure This type of failure often occurs in the failure of the PLC after a certain period of work. In the PLC control loop, if there is a component damage fault, the PLC control system will immediately and automatically stop working. The input circuit is a PLC that accepts switching quantities, analog ...

(1) From the point of view of control methods The control logic of the electrical control system adopts hardware wiring, and the series connection or well connection of the electrical mechanical contact is combined into the control logic, and the connection is complex, large in size, and in large power consumption, and it is difficult to change or increase the function after the system is formed. Other than that...