Soft Touch/Rorobot Finger Module C8V3 Finger height 14mm

Introduction: Rorobot soft jaw BMC-3A18 [HAS]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the fingertip distance of the clamping fingertip G and the external support fingertip distance is D...

Introduction: Rorobot B-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H] and non-marking type [ ...

Introduction: Rorobot Soft Beak B-4B Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Specifications ...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type [H] ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-14 　　Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Rorobot BMC-3B18/S 　　Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking type [ ...

Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BMC-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and non-marking ...

Introduction: Rorobot BML-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and non-marking ...

Introduction:Rorobot Robot Soft Jaw BML-1G364030[HAS]/M, is an enhanced version of the single finger soft jaw, the recommended fingertip and workpiece distance (19-28) mm, the recommended load of one finger soft jaw (0-500) G, the external gripping force (0-11) N. Features: Positive pressure ...

Introduction: Rorobot Finger Module FM-C6V2, Features and Applicable Scenarios: Independent Installation, Can be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module C6V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Finger Module FM-C7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot ACU-MMN Active Driver, ACU-MMN Active Driver--Standard, Mobile Soft Touch Gripper Special Controller, Output Air Pressure -70-120kPa, Manually Adjust the Clamping Force by Knob. Built-in drive air source and battery, can be fully charged without external power supply ...

Introduction: Rorobot B-4B40/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch materials are divided into conventional ...

Introduction: Rorobot Soft Jaw BML-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot module B-4A30/M is a slender soft claw, suitable for jelly shells, test tubes, badminton, cylindrical, hollow columns and other fragile and fragile objects of non-destructive internal support handling and sorting, to ensure that the product will not be scratched, reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: Finger module FM is the action execution module of soft touch gripper, which is composed of two parts: finger F and fixed module, according to the air intake mode, installation position, combination method, select the appropriate finger fixed module. According to the weight and size of the workpiece to be clamped, the size of the required clamping force, ...

Introduction:Rorobot FM-C4V5/LS1[H] Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 3mm Safe working air pressure: 300kPa Recommended load: 70g Self-weight: 20g Our customer-centric approach ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...