IP67 PLC and edge gateway in one bus device – Turck

Turck pressure sensor debugging method example: the 0.08-2MPa planning controller is selected, the pressure is requested to drop to 0.8MPa (down switching value) to announce the contact signal, the operation process is as follows: screw the product into the threaded mouth of the hydraulic pressure calibration table, and ...

Turck's BI1 series of inductive sensors uses a wear-free and touch-free planning method to detect metal objects. Because of its special multi-coil planning, it has quite a few advantages. They have large detection intervals, a great degree of rig freedom and operational reliability, and then further ...

Turck's pressure sensors have good machining and heat treatment functions and have high compressive strength. Affected by the characteristics of low temperature, the correct selection of elastic sensitive components and strain gauge bridges is an important way to improve the strain gauge sensor: 1. High measurement range light accuracy, force sensing ...

Turck has added a new member to its IO-link junction box portfolio with 16 universal channels (digital input or output). Turck presents a new I/O junction box with 16 universal channels.

1. The application of displacement sensor in the shield machine In the tunnel construction equipment, the structural characteristics and supporting facilities of different forms of shield machines are also different. In some messy shield machines, the functions of the shield machine are systematic and diversified. Including: mechanical, hydraulic, ...

The sensor uses a specially shaped rotor and wire-wound coil to simulate the linear displacement of a linear variable differential transducer (LVDT), which has high reliability and functionality, and the rotary motion of the rotor shaft produces a linear output signal that moves around the factory-preset zero position ± 60 degrees (120 in total). This...

The infrared sensor is a very important part of the infrared detection system, but it is very delicate, and if you are not careful in use, it may cause damage to the infrared sensor. Therefore, the following points should be paid attention to in the application of infrared sensors: 1. Must ...

1. Straightness The degree to which the practical connection curve between the sensor output (voltage) and the input (torque) deviates from the ideal straight line. General requirements: ≤ ±2%. 2. Hysteresis The difference in voltage between all test positions during the test stroke. General Requirements: ...

Pressure sensors have been widely used in recent years, many products are in use, according to different types of test pressure, pressure sensors can be divided into gauge pressure sensors, differential pressure sensors and absolute pressure sensors, what are the strain characteristics of pressure sensors? ...

LVDT displacement sensor has a very high measurement accuracy, mainly used for accurate measurement of displacement and position in use, so do you know what is the influence of temperature on LVDT displacement sensor? Effect of temperature change on the output signal ...

1. Eddy current proximity switch This type of switch is sometimes called an inductive proximity switch. It is the use of conductive objects to produce eddy currents inside the object when approaching the proximity switch that can generate an electromagnetic field. This eddy current reacts to the proximity switch and causes the internal circuit parameters of the switch to change, ...

Modularity will win over the field of mechanical engineering, but it is fully in line with expectations and reasonable. Other occupations may have successfully transitioned from craft production to continuous production. In the case of continuous production, the power can be increased through large-scale production. The monotonous process will be automated, so that the employee ...

(1) Long detection intervals If the detection interval of more than 10 m is maintained in the through-beam type, other inspection methods (magnetic, ultrasonic, etc.) can be completed. (2) There are few constraints on the detected object Because with ...

A differential pressure sensor is a sensor used to measure the difference between two pressures, and is generally used to measure the pressure difference between the front and rear ends of a certain equipment or component. Typical Applications: It is used to measure the exhaust particle trap (DP ...

1. The proximity sensor cannot confirm how far the distance between the detected objects is. 2. The switch is installed within the detection interval range, and the signal is sometimes absent (sometimes detectable, sometimes undetectable) in practice. 3. Practice the detection interval and the ...

The most common models of TURCK proximity sensors are recommended Proximity switch NI5-P12SK-YIX Proximity switch BI3U-P12SK-AMN6K Proximity switch BI5-P18SK-AP6X Proximity switch NI10-K20SK-...

Turck's linear displacement sensors have an additional measuring stroke of 100 to 4500 mm. It uses the magnetoelastic principle and non-touch measurement method, and provides a high accuracy of μm according to the 16-bit D/A conversion resolution. It can be changed according to the actual application needs through a very simple programming method.

Turck's BCT sensors feature teachable pushbuttons and LEDs at the rear of the body for maximum user convenience. Turck is presenting a new generation of capacitive sensors from the BCT series, which are primarily used for level detection. Use...

Ultrasonic sensors In order to ensure the best material flow, the in-plant logistics system often uses conveying equipment, and if you want to run the conveying equipment at high speed, it is necessary to obtain the location information of the container. Turck's RU50 ultrasonic sensor is the ideal solution for inspecting containers in intralogistics systems.

The safety relay is a safety loop with all the necessary control parts, which accepts the safety input, and after the internal circuit discrimination, the deterministic output switching signal to the control circuit of the equipment. To put it simply, the safety relays are all two-channel signal type, and only two channel signals are positive.