Common models of IFM temperature sensors

RTDs and thermocouples are the most commonly used temperature sensing elements for temperature sensors. The operating principle of thermocouple temperature sensor is that the two ends of the contact surface of two kinds of incompatible metals produce a weak and weak voltage when the temperature is inconsistent, and the temperature is measured by expanding the electric, which is not necessary to measure the high temperature. RTD Temperature Sensors ...

The sensitivity of the sensor is one of the most basic goals of the sensor. The sensitivity of the sensor directly affects the measurement of the oscillation signal. It is not difficult to understand that the sensitivity of the sensor should be determined according to the size of the oscillation (acceleration value) to be measured, but since piezoelectric acceleration is a measurement of the acceleration value of the oscillation, ...

ifm has the widest range of IO-Link sensors on the market. The new RFID antenna further completes the original product variety. The RFID antenna is planned to connect to the IO-Link master. The master* can supply up to 8 M12 sockets for easy connection to IO-Link RFID antennas. IO-Link Master ...

There are two kinds of proximity switches: NPN output type (current inflow) and PNP output type (current outflow), when the current outflow sensor (PNP output type) is turned on, the current flows from the power supply to the load through the output terminal of the sensor, enters the load, and then flows to the connection.

1. Pay attention to the reasonable distribution of three-phase load In the distribution of three-phase loads, power operators should carefully collect and record the relevant data in the practical operation, so as to be able to guess the status of the electricity load to a certain extent. Secondly, to be able to ...

The TCC temperature sensor was unanimously recognized by the jury and won the Red Dot Design Award 2020 for its cost-effective solution with its excellent design, ideal cleaning performance and high-quality materials. ifm TCC ...

1. Sensor scale: 1) Normal use (static experiment or quasi-static experiment, when the frequency of application is not high, the scale of the sensor should be selected to consider the measured force value, as well as the component of the auxiliary tool (test fixture), etc.). 2) When used dynamically, the scale of the sensor is generally larger than the ...

The oil level sensor according to the resistance is mechanically connected to the float, and the float can rise or fall with the fuel level, and the resistance of the sensor changes as the float moves. The sensor used is part of the current balance circuit in the fuel gauge display circuit, which is generally used to drive ...

1. Inspection distance Detect the stop, start and orientation of elevators and lifting equipment; Detect the orientation of the vehicle to avoid collision between two objects; Detect the setting orientation of the operating machinery and the limit orientation of the moving machine or components; Detect the abort azimuth of the rotary body, the opening or closing of the valve; Detection of cylinders or hydraulic ...

The magnetic switch is different from our common switching devices, it is also called a magnetic switch, which is a line switching device that uses magnetic field signals to control. Perhaps many people will be interested in this new type of switch, so let's make a detailed explanation of the operating principle of the magnetic switch. ...

Diagnose sensor faults based on mathematical models? When there is a problem, the first time is to diagnose it, see where the problem is, so that it is easy to deal with, from different angles, we use more than one method when diagnosing the problem, if this is classified, it can be divided into two ...

1. It is necessary to insist on parallel between the front end surface of the photoelectric sensor and the surface of the workpiece or object to be detected, so that the conversion efficiency of the photoelectric sensor is high. 2. When installing and welding, the root of the pin of the photoelectric sensor and the pad ...

Optical fiber sensors and photoelectric sensors are two typical sensors, which are widely used in production and measurement, so what is the difference between the two? Next, we will analyze the differences between the two from the perspective of principle and use. ...

1. It is necessary for the sensor to be properly installed Damage to high-temperature pressure sensors is usually caused by their installation in improperly machined holes. When the sensor is loaded into a hole that is too small or eccentric, the sensor diaphragm may be damaged, which can then cause the instrument to not function properly. Can...

1. S-type load cells are moderately priced and suitable for mass production - good sensor consistency is required, suitable for automated batch production, and high requirements for processing equipment to eliminate inconsistencies and faults formed by manual operation. 2 ...

1. After the wireless sensor device is installed, it appears to be beating or the number is inaccurate Reason: There is electromagnetic interference on the site, or the signal line and the power line go to the same trunking. Solution: The product function selected by the customer does not meet the on-site working conditions, and it needs to be installed or replaced.

360-degree comprehensive dissection from the inside to the outside, the perfect characteristics of the net red PN series pressure sensor Superior corrosion resistance Ordinary pressure sensors use metal diaphragms, and PN pressure sensors use ceramic diaphragms to sense pressure, ...

2.1 Inspection interval Detect the stop, start and orientation of elevators and lifting equipment; Detect the orientation of the vehicle to avoid collision between two objects; Detect the setting orientation of the operating machinery and the limit orientation of the moving machine or components; Detect the abort azimuth of the rotary body, the opening or closing of the valve; Detection of cylinders or hydraulic ...

The S-type sensor is actually a deformation of the parallel beam structure, so it is not only highly accurate but also easy to use, and has many applications, such as the modification of hopper scales and weighbridges. S-type sensors are now widely used in industrial manipulation and inspection sites. Because of its high-frequency dynamic response, it is mainly used for ...

1. The wiring socket is connected at both ends of the inductance coil, and the other two ends are connected to the liquid level signal input end of the secondary instrument. When the inductor coil is open or the internal circuit is blocked, it should be replaced in time. 2. In order to commission and repair IFM ...