We offer a wide range of barriers for different needs

A device that converts the value of a force transducer into an associated electrical signal. Force is the direct cause of changes in the motion of materials. Force sensors can detect tension, tension, pressure, components, torque, internal stresses, and strains. The specific equipment is metal strain gauges, pressure sensors, etc., which have become electric ...

1. Grating pollution This will reduce the signal output amplitude, and the oil must be quietly wiped off with absorbent cotton dipped in anhydrous alcohol. 2. Encoder connection cable failure: the probability of this fault is high, and it is often encountered in maintenance, so it should be a priority element. Generally, the encoder cable is broken ...

The premise of load cell replacement is that the axis of the applied force coincides with the axis of the sensor, we should know one thing, that is, with the increase of the additional load, the microvolt/indexing signal output by the sensor decreases. About the electromechanical junction of the S-shaped sensor installed in the second force transmission link ...

P+F encoders are devices that compile signals (e.g. bit streams) or data and convert them into signals that can be communicated, transmitted, and stored. The P+F encoder converts angular or linear displacements, the former known as the code disc and the latter into an electrical signal. Therefore, the phenomenon: 1, ...

A sensor is an input device that receives a signal or stimulus and responds to it. Some sensors now integrate many sensing elements and readout circuitry into a single silicon chip, which then provides high accuracy and multiple functions. The new sensor has more functions, including user friendliness.

1. Each electrical interface has its own characteristics, but also has different baud rate and transmission interval, which can be selected according to the specific application environment of the site, and the actual transmission interval is very related to the transmission rate, encoder and communication cable installation disturbance environment, grounding, cable material selection, etc. ...

1. It is necessary for the sensor to be properly installed Damage to high-temperature pressure sensors is usually caused by their installation in improperly machined holes. When a sensor is loaded into a hole that is too small or has a migraine, it may damage the sensor diaphragm and cause the instrument to not function properly. Can...

Rotary encoders are a class of sensors used to detect the angle of rotation and its derived mechanical parameters, including velocity and acceleration, etc., and can detect transmission movements such as rotation and linear lines. Due to its wide range of applications, rotary encoders convert mechanical inputs into electrical signals, which can be used by counters, tachometers, programmable ...

Autonomous mobile robot AMRs typically use LiDAR photoelectric sensors to detect objects. These photosensors emit light and rely on reflection to measure the distance to a specific surface. It's a great way to detect a solid object, but it can present challenges when it's surrounded by a transparent material such as glass. ...

In the process of application, the sensor will inevitably be affected by the environment, temperature, dust and other factors, so that the equipment is aging or wearing, and if these problems are not dealt with in time, it will bury potential troubles for the future use of the equipment, resulting in large and small problems, and ...

Like many other types of sensors, torque sensors are measured using strain gauge technology. The sensor is usually a metal elastomer with a strain gauge mounted on it. Strain gauges are firmly attached to the elastomer. If an external load acts on the sensor, the measuring body will ...

1) It is recommended to place the pressure sensor and its tee valve at the level of the axillary line, which is used for ventilation and sensor zeroing. 2) Approve the maintenance cap on the three-way valve to be perforated, connect the sensor with the monitor, and follow the instructions of the monitor to ...

The safety barrier, also known as the safety energy limiter, is an important part of the intrinsic safety system. There are two main types of safety barriers: P+F Zener barriers and P+f barrier barriers. The core components of the Zener barrier are Zener diodes, current-limiting resistors and fast fuse wires. ...

Torque sensor is a sensor widely used in the mechanical category, which can measure the torque of rotating objects, and torque sensors have a wide range of application scenarios, and several typical application scenarios will be introduced below. First of all, the short-term sensor is widely used in the automotive industry to measure the engine and transmission.

Types of load cells: Electrical strain gauge load cells: One widely used principle is the color of a resistive strain gauge (resistance strain gauge), where the resistance is changed to an electrical output, which is then passed through an instrument to measure the mass. Capacitive load cells: low power consumption and low cost. The principle of ...

The new RHI90 series encoders offer significant improvements in electrical and mechanical performance With the extensive use of electronic components and equipment in the field of automation, the risks of malfunction and damage caused by electrical and electromagnetic disturbances are also invisible.

1. Select the type of proximity switch according to the detected object. If the detection object is metal, the inductive proximity switch is preferred, and if the detection object is non-metal such as wood, plastic, paper, water, etc., or smaller and finer metals, the capacitive proximity switch should be selected. ...

The first is pressure, and the transmitter can't afford to lose it. In this case, see if the pressure connector is leaking or clogged, if you admit that it is not, look at the wiring method and see if the power supply is normal, simple pressure to confirm if the output has changed, or if there is an output at the zero point of the sensor ...

With the rapid development of automation technology, what kind of RF identification skills can be called "cutting-edge"? Reliable identification + seamless data transmission + continuous system operation, these three points are indispensable, and the UHF F190/F192 series launched by Bejiafu is a combination of many advantages. On a global scale ...

Under normal circumstances, a photoelectric sensor consists of two parts: a processing path and a processing element. Its basic principle is to use the photoelectric effect to convert the measured change into a change in the optical signal, and then use the optoelectronic components to further convert the non-electrical signal into an electrical signal. The "photoelectric effect" refers to the use of light ...