Omron announces the opening of its California Robotics Headquarters

Recently, Omron and Inner Mongolia Guoda Pharmacy jointly built the first MMC health convenience store in Hohhot. The strong alliance in the field of health care aims to actively respond to the policy requirements of the national "new medical infrastructure", help the standardization of chronic disease services in offline stores, and make ...

Recently, the 2022 P&G Electrical Automation Seminar held by Procter & Gamble (China) Co., Ltd. (hereinafter referred to as "P&G") was held in Guangzhou. Omron Automation (China) Co., Ltd. (hereinafter referred to as "Omron") was invited to attend the meeting and worked with the engineering, manufacturing, R&D and other departments of P&G factories on behalf of the ...

In the design of switching power supply, the physical design of the PCB board must be proper, otherwise it may cause excessive electromagnetic interference and lead to unstable power supply. 1. The design process from the schematic diagram to the PCB should be rigorous and perfect: the establishment of component parameters ...

From November 5th to 10th, the 5th China International Import Expo was held in Shanghai, where multinational companies from all over the world gathered to participate in the annual international economic and trade event. As a global expert in digital transformation in the field of automation, Omron has entered the ...

First, the contact point is loosened and cracked The contact point is the electrical contact part of the Omron relay to convert the load, and the contact point of some products is matched with each other by riveting pressure, and the key disadvantage is that the contact point is loose, the contact point is cracked or the error of the standard part is too large. This will jeopardize the relay ...

One. The surface of the Omron relay shell installed and used should be free of scratches, cracks and damage, and if there is serious damage, the relay should be replaced in time with intact and the same specification; Two. In the process of Omron relay maintenance, it is necessary to check whether the contacts of the Omron relay are ...

1. External equipment failure. Such faults come from external devices such as various sensors, switches, actuators, and loads. The failure of this part of the equipment will directly affect the control function of the system. This type of failure is usually caused by the quality and longevity of the equipment itself. 2. System failure ...

Omron Automation (China) Co., Ltd. (hereinafter referred to as "Omron") officially launched the Components product section on its official website. A huge product lineup of more than 200,000 pieces, carrying ingenuity and quality, can cover almost all the needs of the production site, help the comprehensive evolution of the production site, and empower the future wisdom.

1) Expand the scope of control. For example, when the control signal of a multi-contact relay reaches a certain value, it can be changed, interrupted, and connected to multiple circuits at the same time according to the different forms of contact groups. 2) Zoom in. For example, sensitive relays, intermediate relays, etc., with a very small control ...

1. Double-click "CX-Programmer" to open the programming software 2. Click on "PLC" and select "Change Communication Settings (U)" 3. Pop up "Modify PLC network settings" and select "USB" or "Toolbus (USB port)" as the driver 4. Click on the "Yellow Lightning" symbol ...

On May 12, Omron Health Care (China) Co., Ltd. and Xi'an Yikang Pharmaceutical jointly built Xi'an Yikang Pharmaceutical Youyi West Road Store MMC Health Convenience Store (No. 105, 1st Floor, Life North District, Optical Machinery Institute, No. 121 Youyi West Road, Beilin District, Xi'an City) was officially opened and put into operation. The double ...

There are 3 types of micro switches, which perfectly match the precise control needs of household appliances Micro switch refers to a contact mechanism with a small contact spacing and a snap-action mechanism, a contact mechanism that carries out the switch action with a specified stroke and a specified force, covered with a shell, and a drive rod on its outside, ...

Equipment Overview The stack welding machine is mainly used for the overlap welding of monocrystalline and polycrystalline cells in fully automatic crystalline silicon solar cell modules, and is suitable for series welding of small-size crystalline silicon solar cells.

1. C200H series PLC fault codes: - E0001: Undefined program error - E0002: Undefined instruction error - E0003: Missing Program Error - E0004: Data error - E0005: Pointer error - E0006： ...

1. Standard configuration with RS485 interface, Modbus bus communication function; 2. At 3Hz, it can provide more than 150% torque output and start quickly; 3. The carrier frequency of 2-15KHz is adjustable, which can realize silent drive; 4. Equipped with simple energy-saving function; 5. Controlled ...

Process introduction In the middle process of the secondary battery, the battery welding machine first needs to quickly heat press the battery cells after winding/lamination to achieve cell compaction, and then ultrasonic welding of the positive and negative tabs of the battery cells. 　　problem 1. Pressure fluctuates greatly, causing ...

As the world's top electronic sphygmomanometer manufacturer, Omron electronic sphygmomanometer has been sold to 138 countries around the world and is still a world-renowned electronic sphygmomanometer brand. With nearly 50 years of experience in the field of blood pressure management, Omron has always been committed to serving the health of Chinese residents.

1. Measuring contact resistor Use the resistor file of the universal meter to measure the normally closed contact and the moving point resistor, and its resistance should be 0; The resistance of the normally open contact and the moving point is infinite. This makes it possible to distinguish which is a normally closed contact and which is normally open. 2. Test the coil resistance ...

1. CPU unit address allocation Type X and XA CPUs The X and XA CPU units come with 40 I/O, of which 24 are inputs and 16 are outputs, and the input part of the CIO area occupies 0 - 1 channel, with a total of 24 input bits: 12 of these bits are 0 bits of channel 00—— ...

Process introduction In the traditional die-cutting process, because the cutter cannot cut the material completely, the connecting frame will be left, which increases the cost of the material. In addition, the service life of the die-cutting knife is 1 million times, such as long-term continuous operation, it needs to be replaced and maintained in time, and the maintenance and debugging time is also very long.