P+F encoders are devices that compile signals (e.g. bit streams) or data and convert them into signals that can be communicated, transmitted, and stored. The P+F encoder converts angular or linear displacements, the former known as the code disc and the latter into an electrical signal. Therefore, the phenomenon: 1, ...

The displacement sensor has no sliding contacts, is not affected by non-metallic elements such as dust during operation, has low power consumption, and has a long service life, so it can be used in various bad conditions. Displacement sensors are mainly used to intelligently control the analog quantity of automation equipment production lines. The displacement sensor selects laser three...

First, pay attention to the capacitive and inductive resistance of cables and field equipment, explosion-proof is the system explosion-proof, in addition to the need for P+F safety barriers to reach the required explosion-proof level, the energy storage of cables and field equipment is also a key issue. Especially after the parametric certification replaces the system certification, the engineering company has a special ...

In electrical intrinsic safety explosion-proof, we generally divide the workplace into explosion-proof areas and non-explosion-proof areas. There is the transmission of electrical energy between the explosion-proof area and the non-explosion-proof area, for example, the switches, buttons, sensors, etc. in the explosion-proof area are connected to the PLC placed in the electrical cabinet in the non-explosion-proof area through wires.

A photoelectric sensor is a device that converts optical signals into electrical signals. Its principle of operation is based on the photoelectric effect. The photoelectric effect refers to the phenomenon that when light hits some substances, the electrons of the matter absorb the energy of the photons, and 7 the corresponding electrical effect occurs. According to the different phenomena of the photoelectric effect, the light ...

1. Conceptual sensor: It can sense the specified signal under test and correlate the signal into an electrical signal. Transmitter: Comply with the necessary algorithm rules to convert the measured electrical signal into a standardized industrial control signal. (1) Sensitive element refers to the sensor that can directly (or as a response) ...

Proximity Switches: NBB2-12GM50-E2 NBB2-12GM50-E0 NBN4-12GM50-E2 NBN4-12GM50-E0 NBB5-18GM50-E2 NBB5-18GM50-E0 NBN8-18GM50-E2 NBN8-18GM50-E0 NBN15-30GM50-E0 NBN15-3 ...

According to the principle of operation: Potentiometer-type displacement sensor It converts the mechanical displacement through the potentiometer element into a resistive or voltage output that is linearly or arbitrarily linked to it. Generally, linear potentiometers and round potentiometers can be used as linear and angular displacement sensors, respectively. ...

In the process of modernization, the SLP series is gradually forming a modular safety system, constantly innovating, and requiring more stringent quality on the basis of innovation. VISOLUX offers safety light curtains for a wide range of light beams. These self-monitoring lights ...

From leveling cranes and monitoring the inclination of front-end loaders to operating elevators, inclination and acceleration sensors can be used in a variety of ways. These sensors are guaranteed to measure even in harsh conditions. Thanks to the innovative split unit concept, the F99 series ...

NBB20-L2-E0-V1/ NPN normally open NBB20-L2-E2-V1/ PNP normally open NBB20-L2-A2-V1/ PNP normally open + normally closed NBN40-L2-Z0-V1/ DC two-wire normally open NBN40-L2-E0-V1/ NPN normally open NBN40-L2-E2-V1/ PNP normally open ...

The R2 and R3 series of photoelectric sensors are impressive products that characterize a very small housing plan. Robust R2/R3 miniature photoelectric sensors – smaller than a matchbox, space-saving miniature housing photoelectric sensors R2/R3 series ...

1. Grating pollution This will reduce the signal output amplitude, and the oil must be quietly wiped off with absorbent cotton dipped in anhydrous alcohol. 2. Encoder connection cable failure: the probability of this fault is high, and it is often encountered in maintenance, so it should be a priority element. Generally, the encoder cable is broken ...

In addition to getting used to mechanical shock, pressure, and tensile strain, sensor cables are often exposed to chemical environments. While traditional sensor cable planning is often not sufficient to meet these requirements, the new cable maintenance system has been developed with this intention in mind, guaranteeing ...

1. The safety barrier should be installed in a safe place, and the environmental conditions meet the requirements of "application conditions" in the "Safety Barrier Selection Sample". 2. The connecting wires of the intrinsically safe end (blue end) and non-intrinsically safe end circuits of the barrier safety barrier should be laid separately in the wiring slot.

1. Test for NPN output sensor The NPN sensor output, also known as OC gate output, is based on the principle of open collector output of a transistor. The principle of NPN type OC gate output is whether the output of the NPN transistor and GND are short-circuited. When the transistor is turned on, the output and GND ( ...

The company is a company focusing on the development of mechanical motion control and sensing skills, and its products have the characteristics of high reliability, high accuracy and high protection, and play an irreplaceable role in the process of industrial production and mechanical manufacturing. ...

Rotary encoders are a class of sensors used to detect the angle of rotation and its derived mechanical parameters, including velocity and acceleration, etc., and can detect transmission movements such as rotation and linear lines. Due to its wide range of applications, rotary encoders convert mechanical inputs into electrical signals, which can be used by counters, tachometers, programmable ...