When using an inverter, a leakage maintainer must not be used. This is a major principle of the use of frequency converters.
Some users choose the corresponding leakage maintainer for the inverter when using the inverter. * The result is: the inverter moves together, the leakage maintainer acts, and the system base cannot operate. Why?
The principle of a leakage maintainer is that the zero sequence current is zero. When using an inverter, the zero sequence current cannot be zero.
The output side of the inverter is a PWM wave, and there is a capacitive effect of a long cable between the motor cable and the ground, which is more obvious when using a shielded cable. When the inverter is operating, the capacitor is charging and discharging, and the current flows into the ground through the capacitor, and flows back to the inverter from the grounding wire on the incoming side to form a current loop. If a leakage maintainer is used on the inlet side, it will operate and the blocking system will operate. So, don't equip your drive with a leakage maintainer. If you want to ensure safety, you just need to do a good job of grounding the equipment.
Example: Q: An 18.5KW boiler induced draft fan is installed with an 18.5KW inverter, as soon as the inverter is installed, the distribution room will jump when it is opened, and the power distribution room is equipped with a leakage maintainer (200mA action, 30mA pulse). The customer was asked to remove the leakage maintenance was refused, and then the carrier frequency was adjusted to 1KHz, and the inverter was still not solved by changing the inverter starting mode, and the power line of the motor was suspected to have leakage, because its length was about 20 meters and buried in the ground, but it was also difficult to require the customer to replace it (its original power frequency was used normally). Is there a simple and effective solution?
Answer: Because the leakage maintainer generally detects that the three-phase unbalance is more than %20, it will skip maintenance, and when the three-phase unbalance degree is installed after the inverter, the three-phase unbalance will generally exceed %50 or more, so the leakage maintainer will definitely jump.
Here are a few ways to do it:
Method 1: There will generally be an adjuster on the leakage maintainer, and the regulator can be adjusted to a larger size.
Method 2: Replace the leakage maintainer with a special leakage maintainer for the inverter, and there are special leakage maintainers for the inverter on the market.
Method 3: Increase the load of the equipment, that is, the load of the motor, and the leakage current of the inverter will not be very large when it is started.
Method 4: Short the leakage maintainer.
|
More on that
|
Introduction to vector control of inverter and motor - LS power generation
As for the use of vector-operated motors, it can be divided into two categories, namely non-reactive vector control (SVC) and reactive vector control (FVC). Vectorless Handling (SVC): Due to the speed response, additional equipment for the encoder is installed in the motor dragged by the inverter, which is cumbersome. Here...
|
|
The essence and use of LS power PLC module
1. What is PLC?
PLC control system, Programmable Logic Controller, programmable logic controller, a digital operation of electronic devices specially designed for industrial production planning, it uses a class of programmable memory, used in its internal storage program, the execution of logic...
|
|
Basic introduction to transistors - LS produces electricity
A transistor is a solid-state semiconductor device with a variety of functions such as detection, rectification, amplification, switching, voltage regulation, and signal modulation. A transistor is a variable current switch that can manipulate the output current based on the input voltage. Unlike general mechanical switches (e.g. Relay, swit...)
|
|
DC reactor for inverter and design calculation - LS power generation
The DC reactor for the inverter is also called the flat wave reactor, which is connected in series in the DC bus (terminals P1 and P+). The main thing is to reduce the higher harmonic component of the input current and improve the power factor of the input power supply (to 0.95). This reactor can be used at the same time as the AC reactor, and the inverter has high power ...
|
|
LS power inverter function
1. Soft up
The direct launch of the inverter motor has a serious impact on the power grid, and it will also have too high requirements for the capacity of the power grid, which is extremely unfavorable to the service life of equipment and power grid circuits. After the use of inverter to save energy, the use of inverter's speed regulation (V/F) function will make the starting current from a small ...
|
|
Briefly describe LS ABE203b molded case circuit breaker
The circuit breaker is a fundamental low-voltage electrical appliance, which has the function of overload, short circuit and undervoltage maintenance, and has the ability to maintain the line and power supply. Circuit breaker is an indispensable product in electrical safety. Due to different applications, there are molded case circuit breakers, frame circuit breakers, miniature circuit breakers, etc.
|
|
Types and characteristics of PLC digital output modules for power production
The main functions and functions of PLC:
1. For sequential control: sequential control is based on the current and pre-historical situation of the input switch, and produces the required switching output, so that the system can operate in a certain order. ...
|
|
The cause of motor burnout caused by the inverter - electricity production
In fact, the fault of the motor is not the cause of the motor itself, most of them are caused by the non-standard debugging of the inverter or the wrong inverter motor when the inverter motor is used, etc., mainly in the following situations:
1. Treat the general motor as a ...
|
|
Introduction to the control method of LS power inverter
Inverter control method: low-voltage general frequency conversion output voltage is 380-650V, output power is 0.75-400kW, operating frequency is 0-400Hz, and its main circuit adopts AC-DC-AC circuit. Its control methods have gone through the following five generations.
1U/f=C sine pulse width modulation ...
|
|
Inverter maintenance fault handling method - LS power generation
1. Not manifested. This situation is more common, generally in the normal condition of the external three-phase power supply, it is the switching power supply of the inverter burned, and the 24 volt power supply on the output board of the inverter terminal can be measured.
|
|
Safety precautions for LS inverters
1. When the power supply is now powered or the inverter is in operation, do not open the shell of the inverter. Otherwise, an electric shock may occur.
2. When the front cover of the inverter is opened, do not run the inverter. Otherwise, you may be subjected to ...
|
|
Precautions for the peripheral configuration of the inverter - LS generates electricity
(1) When the inverter is connected to the power grid of large-capacity power transformer (more than 500kVA), perhaps the same power transformer is connected with a thyristor converter without using a commutation reactor, or when there is a switching capacitor bank for power improvement in the same power grid, an AC reactor or DC reactor should be equipped.
|
|
Servo drives and servo motors – LS produces electricity
Driver: Under the premise of carrying out frequency conversion skills, the servo drive has carried out more advanced control skills and algorithm operations than general frequency conversion in the current ring, speed ring and azimuth ring inside the drive (the frequency converter does not have this ring), and it is much stronger than the traditional servo in terms of function.
|
|
Six misunderstandings in the installation and use of inverters - electricity production
Myth 1: Connect electromagnetic switches and electromagnetic touches in the output circuit of the inverter
In practical application, some occasions need to use the touch device for frequency converter switching: such as switching to the power frequency state when the frequency conversion is faulty, or the election is used to drag two methods, a motor is faulty, and the variable frequency is used.
|
|
Inverter fault diagnosis - LS power generation
1. How to distinguish between heavy and light faults
When there is a problem with the light, the system announces the alarm signal and the fault indicator flashes. When there is a serious problem, the system will announce the problem indicator, the problem indicator will always be on, together announce the order to break the high voltage and stop closing, and store the problem ...
|
|
Introduction to wiring problems - LS power generation
1. Wiring of fire emergency lighting
Generally, the flame retardant wire is used to wear the metal pipe and the thickness of the protective layer is ≥ 30mm.
|
|
The cause of motor burnout caused by inverter - LS generates electricity
In fact, the problems of the motor are not the cause of the motor itself, most of them are caused by the non-standard debugging of the inverter or the wrong inverter motor when the inverter motor is used, etc., mainly due to the following situations:
1. Put the general motor ...
|
|
Introduction to LS Master-K series PLC programming
LS is an electrical equipment company affiliated to LG, kglwin3.62 programming software Chinese version is a professional plc programming software designed to help daily more efficient planning and development software, the software supports the programming and debugging of LG Master-K series and LG MASTER-K series, and provides ...
|
|
LS static test to determine the fault of the inverter
Generally, the general-purpose inverter roughly includes the following parts: (1) rectifier circuit; (2) DC central circuit; (3) Inverter circuit; (4) Control circuit. The static test is mainly a test of the high-power transistors (power modules) of the rectifier circuit, DC center circuit and inverter circuit. Whole...
|
|
Introduction to the matching of LS power inverter loads
1. Square torque load
Fan and pump loads are the most widely used equipment in industrial sites, and frequency converters are used in this type of load. It is a square torque load. In general, inverters with U/f=const control mode can be satisfied with the ...
|
|
Contact
working hours
