Introduction: The H-Series can be connected to hazardous area field devices and control systems by mounting multiple isolation barriers on terminal boards. Compared to a single interface module, the terminal block greatly simplifies wiring and saves costs. The terminal block is equipped with a sturdy plastic housing for quick and secure installation in the cabinet. There are multiple mounting slots on the terminal board, allowing engineers to install the isolation barrier on the terminal board without the use of tools. The isolation barrier module is hot-swappable. Optional fault monitoring terminal blocks make operation and maintenance even faster. Pre-assembled cables with cable connectors simplify design and documentation. These cables replace the cumbersome point-to-point wiring between the terminal board and the controller I/O card (DCS, ESD).
Product Details
H series interface module
The H-Series interface modules can be easily plugged into the terminal block without any auxiliary tools and cable wiring. The intrinsically safe field signal of the module is electrically isolated from the non-intrinsically safe test in the safe area.
The main features of the H-series interface modules are high channel density, space-saving, single-loop integration and easy start-up commissioning.
HID interface module
The HID module has a width of 18mm and is mainly characterized by high channel density, low power consumption design, and SIL2/3 rating. The 16-slot terminal block** can be connected to up to 64 channels.
HIC interface module
The width of the single-channel HIC interface module is only 12.5mm, and the main feature is single-loop integration, SIL2/3 level, saving cabinet space up to 33%. The low-power design makes the temperature in the cabinet low** and prolongs the life of the module. Despite the fact that many modules are installed in a single cabinet, the heat dissipation is extremely low.
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only by being professional and careful in every process, every action and every detail of the service can we meet or even exceed customer expectations and make customers satisfied and recognize us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces P+F safety barrier module H series 16 slot products, if you are interested in P+F safety barrier module, please also contact our customer service, we look forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F/Through-beam photoelectric sensors LD31/LV31/73c/76a/136
Product Description: Thru-beam sensor, 30 m detection range, red light, switch-on on bright, AC/DC type, relay output, fixed cable, cost-optimized series for standard tasks, small housing for large structures, high visibility LED, universal voltage version, relay output. ...
|
|
P+F Capacitive Sensor CJ10-30GK-WS 10mm non-flush
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
...
|
|
P+F/Capacitive sensor CBN15-30GK60-A0 NPN15mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN5-F46-E0-Y286690 distance 5mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F Zener Barrier Z System 35 mm DIN rail
Introduction: P+F/Plus Forziner Barrier - cost-saving, easy to install explosion protection. Mounted directly on a 35 mm DIN rail. With the accessory, the required grounding can be carried out directly on the DIN mounting rail.
Product Details
Zen ...
|
|
P+F/Inductive sensor NBB4-12GM50-E0 4 mm
Description: The NBB4-12GM50-E0 inductive sensor is rated for a working distance of 4 mm, flush mounting, an extended temperature range of -40 to +85 °C, an extended operating voltage range, and a wide range of mounting options for flexible use.
...
|
|
Germany P+F/Bejiafu inductive sensor NBN30-U1K-N0 weight 225g
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F Capacitive Sensor CBN5-F46-E2-Y70121258
Introduction: P+F Capacitive sensor CBN5-F46-E2-Y70121258 rated working distance of 5 mm, non-flush mounting; DC 3 wire with additional wire for teaching; Flat housing; Fixing grooves for cable ties; Through-holes for screw mounting.
...
|
|
P+F/Sensor NBN4-12GM40-E2-V1 4 mm
Introduction: The inductive sensor is to use electromagnetic induction to convert the measured physical quantities such as displacement, pressure, flow, vibration, etc. into the change of self-inductance coefficient and mutual inductance coefficient of the coil, and then convert the output of voltage or current change by the circuit to realize the conversion of non-electricity to electricity.
...
|
|
P+F/Inductive sensor NBN4-12GM40-E2-T-V1 mass 12g
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F Capacitive Sensor CJ40-FP-A2-P4 4-wire
Introduction:P+F capacitive sensor CJ40-FP-A2-P4 series rectangular, housing material is POM / metal, output type 4 wires, non-flush mounting, DC voltage type, screw terminal connection type, protection class IP65.
...
|
|
P+F Signal Conditioner S1SD-1AI-1C.H Resistance 50Ω
Introduction: The P+F signal conditioner SC series provides isolation in an extremely compact package and is optimized for the application requirements of the safe area. Connected via screw terminals, according to EN 60715:2001, mounted on a 35 mm DIN mounting rail.
...
|
|
P+F/Through-beam photoelectric sensor BB10-P/59/76b/103/115e
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F/2D Laser Scanner R2000 5-pin M12x1 connector
Product Introduction: The R2000 series combines standard sensors with the latest measurement methods. The R2000 2D laser scanner (also known as 2D LiDAR sensor) is equipped with the innovative Pulse Ranging Technology (PRT) to deliver reliable and extremely precise measurement results with 360° gap-free ...
|
|
P+F Inductive Positioning System PMI120-F90-IU-IO-V15
Introduction:P+F Inductive Positioning System PMI120-F90-IU-IO-V15 Reverse Polarity Protection, Analog Current or Voltage Output, Programmable; Linearity ranges from 1 to 119 mm; PBT, stainless steel 1.4571, brass, nickel-plated housing.
...
|
|
P+F/OBE20M-R100-S2EP-IO-V31-L through-beam type
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F/Capacitive sensor CBN15-F64-A2 15mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN15-F64-A2 voltage drop ≤2V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards the proximity switch, whether it is ...
|
|
P+F/VLD700-F280-2E2-1000 laser diode
Product Introduction: Parameterization of the SmartRunner Detector is very simple. The laser line of the vision sensor is projected onto the desired background and programmed using teach-in. With the Data Matrix control code, the user can set additional parameters such as the detection area without a PC ...
|
|
P+F/Triangulation sensor OQT150-R100-2EP-IO 10-30VDC
Product Description: Measurement core technology, 150 mm detection range, red light, IO-Link, 2 x push-pull output, 2 m fixed cable, miniature design with multiple mounting options, Multipixel Technology (MPT) - Flexibility and adaptability, switching diffuse reflection mode sensors, reducing equipment ...
|
|
Contact
working hours
