Pre-assembly requirements for valves

The hydraulic maintenance module uses the hydraulic locking method to control the inlet and outlet oil circuits and load oil circuits of the electro-hydraulic servo valve, and the module has the following three functions: 1. Locking function When the system is in normal condition, the hydraulic lock is in the guide ...

Double-seat cast ball angle valve The nominal diameter is 40-200 mm Nominal pressure ANSI 125, 150, 300, 600JIS10, 16, 20, 30, 40K PN1.6, 4.0, 6.4MPa Connection type Flange...

Knife gate valve is a kind of valve, which is called knife gate valve because of its different structure. It has outstanding circularity through the use of some special media, such as some viscous media, granular media, etc. It solves some of the problems of modern equipment and becomes an indispensable component of modern equipment ...

Routine maintenance of pneumatic conditioning valves When the conditioning valve is packed with graphite-asbestos, lubricating oil should be added to the packing once in about three months to ensure that the conditioning valve is flexible and easy to use. If it is found that the pressure cap of the packing is very low, the packing should be compensated, such as the PTFE dry packing is found to be hardened ...

Scientific and technological innovation, Wuzhong Instrument has gone through a road of deep integration of informatization and industrialization. "There are too many foreign 'stuck neck' technical products. The control valve industry is all-encompassing, with 100,000 varieties and specifications, more than 1 million parts, and more than 5,000 quality control points.

The self-operated conditioning valve, also known as the self-operated control valve, relies on the pressure and temperature of the medium flowing through the valve as the energy source, and uses the reaction signal (pressure, pressure difference, temperature) at the output end of the valve to be transmitted to the actuator through the signal tube, and drives the valve disc to change the opening of the valve and reach the conditioning pressure.

1. What is a chemical centrifugal pump? Answer: It is a machine that adds liquid energy by increasing the effect of centrifugal force through the impeller to increase the mechanical energy of the liquid, so as to transport the liquid. 2. What are the characteristics of chemical centrifugal pumps? Answer...

The selection of control valve is a very complex thing, in order to ensure the use of control valves, customers only need to provide process parameters and use requirements to valve manufacturers, because valve manufacturers have rich experience in valve use, so they can provide customers with the best cost-effective valve products. ...

　　First, the effect of pipeline identification Why do you need to do pipeline identification? Intent: To facilitate the identification of substances in industrial pipelines, ensure safe production, and avoid misjudgment in operation and equipment maintenance. Carry out ...

The structure of the adjustable pressure reducing valve is composed of a main valve, a pressure feedback system, and a control pipeline. The main valve is composed of main parts such as valve body, diaphragm seat, valve cover, diaphragm, valve stem, valve plate, etc. The adjustable pressure reducing valve is installed on the one-way water supply pipeline in the city, which can reduce the upstream (inlet) pressure of the higher valve.

A safety valve is an automatic valve that uses the medium's own force to expel an additional amount of fluid without any external force to avoid the pressure exceeding the additional safety value. When the pressure has recovered to normal, the valve closes again and prevents the continuous flow of the medium. (TSG ZF001-2006)

1. The safety valve should have the equipment to prevent the hammer from moving by itself and the guide frame to restrain the lever from deviating, and the tension spring safety valve should have the equipment to improve the handle and prevent the adjustment screws from being twisted at will. 2. It should be installed straight in the pot merchant, the container ...

Valve application requirements (1) General gate valves, ball valves, and globe valves are prohibited from dispatching according to their structural characteristics. However, in process design, it is widely used for mediation. Because of the scheduling application, the valve seal has been in a throttling state for a long time, and the impurities in the oil have washed the seal, endangering the seal.

The commonly used medium for valve pressure test is water, oil, air, steam, nitrogen, etc., and the pressure test methods of various valves are as follows. (1) Globe valve and throttle valve The strength test of globe valve and throttle valve, usually the assembled valve is placed in the pressure test frame, the valve disc is turned over, and the medium is injected to...

Two-position five-way solenoid valve is a pneumatic component commonly used in gas-electric automatic control system, its main use is to control the double-acting cylinder to complete the automatic switching of the air circuit, widely used in the pneumatic equipment of various industrial parts, to complete the automatic control and long-distance operation in the production process, it has the ability to ...

1. Impurities are stuck on the sealing surface of the valve The valve is sometimes closed suddenly, it may be that there are impurities stuck between the sealing surface of the valve, at this time should not be forced to close, the valve should be opened slightly larger, and then try to close, try repeatedly, it can generally be eliminated, otherwise it should be checked again...

1. The corrosion of the valve is usually understood as the damage to the metal material of the valve under the chemical or electrochemical environmental effect. Because the corrosion phenomenon is presented in the spontaneous interaction between the metal and the surrounding environment, therefore, how to isolate the metal from the surrounding environment or more use non-...

1. Glander type This is the form that is used a lot. The same form can be different in many details. For example, in terms of hold-down bolts, it can be divided into T-bolts (for low-pressure valves with a pressure of ≤ 16 kg/cm²), stud bolts and loose joints. From the gland point of view, it can be divided into integral and ...

Valve is a device used by Gongliang to control the direction, pressure and flow of fluid in the fluid system. A valve is a device that allows the flow or suspension of the medium (liquid, gas, powder) in the piping and equipment, and can control its flow. The valve is a controlling part in the pipeline fluid delivery system, ...

A low-power electromagnetic microdisplacement controller consisting of a coil backbone, a coil wound around a coil skeleton with a control circuit and a terminal block, and a coil core, characterized by: The coil core is associated with two magnetic columns at both ends ...