Analysis of technical problems of Wuzhong instrument chemical centrifugal pump

1. The safety valve should have the equipment to prevent the hammer from moving by itself and the guide frame to restrain the lever from deviating, and the tension spring safety valve should have the equipment to improve the handle and prevent the adjustment screws from being twisted at will. 2. It should be installed straight in the pot merchant, the container ...

The mechanical deflection angle of the movable part of the surface can be measured and converted, and the size to be measured is directly indicated by the indicator, so it is also called the direct-reading appearance. According to the working principle, the indication surface can be divided into magnetoelectric system appearance, electromagnetic system appearance, electric system appearance and ...

A few days ago, in a large digital workshop of Wuzhong Instrument Co., Ltd., the operators were working carefully. Every day, tens of thousands of parts orders are sent from dozens of sales outlets across the country such as Guangzhou and Hainan, and nearly 200 pieces of equipment in the workshop are processed and produced. 　　Because of the working conditions ...

1. The hydraulic power in the hydraulic ball valve should refer to the opening mode of the valve as hydraulic, which refers to the valve opening device. The latter ball valve refers to the valve type as a valve type and a shut-off valve class. Two: Type Q61N can explain Q as ...

1. Flange connection Flange connection: Flange connection refers to the detachable connection of flanges, gaskets and bolts as a group of combined sealing structures. Pipeline flange refers to the flange used for piping in pipeline equipment, and refers to the inlet and outlet flange of equipment used in equipment.

Insist on the cleanliness of valves and actuators as much as possible. The valve is drained after the flow test. During storage and installation, it is important to avoid the ingress of contaminants. Assuming that there is a problem, check it according to the instructions. Do not use a crowbar or an excessively large ...

The selection of control valve is a very complex thing, in order to ensure the use of control valves, customers only need to provide process parameters and use requirements to valve manufacturers, because valve manufacturers have rich experience in valve use, so they can provide customers with the best cost-effective valve products. ...

Classified by role and use (1) Shut-off valve: The shut-off valve, also known as the closed-circuit valve, has the effect of turning on or cutting off the medium in the pipeline. Shut-off valves include gate valves, globe valves, plug valves, ball valves, butterfly valves and diaphragms. (2) Check valve: Check valve is also known as check valve or check valve.

1. The valve core is pressure balanced, even if the large-diameter valve is under the high pressure drop parts, it can also be operated with a smaller actuator. 2. The inner cavity of the valve is straight-through streamlined, which greatly reduces the activity resistance. 3. The concentric movement method of the valve core and the valve body is greatly ...

The shut-off valve is a kind of actuator in the automation system, which is composed of a multi-tension spring pneumatic membrane actuator or a floating piston actuator and a regulating valve, which receives the signal of the regulating instrument and controls the blocking, switching or switching of the fluid in the process pipeline. It has a simple structure, sensitive response, and ...

1) General purpose valve (general purpose valve): a general term for a wide range of valves, also known as ordinary valves. It is not a valve for a specific condition and a specific purpose. Although there is no clear definition of a universal valve, it mainly refers to a pressure below 2MPa, ...

1. Accounting for traffic The calculation of the flow rate can also be confirmed by referring to the capabilities of fluid handling machinery such as pumps and compressors. Sometimes, a combination of methods is used to confirm. 2. Confirmation of the differential pressure (1) Put the conditioning valve before and after ...

The actuator of the control valve has pneumatic type, electric type and electro-hydraulic linkage type, and the pneumatic equipment is divided into barrier type and cylinder type. Depending on the action when the operating signal and the drive source disappear, the actuator has a forward type, a reverse type, a non-directional type, and a persistent type. The positive type is used in the operation signal and drive ...

In all kinds of mechanical connectors, the anti-loosening of bolts is a very important link. So can the tension spring washer be loosened? The principle of anti-loosening of the tension spring washer The anti-loosening principle of the tension spring washer is that after flattening the tension spring washer, the tension spring ...

Valve application requirements (1) General gate valves, ball valves, and globe valves are prohibited from regulating according to their structural characteristics. However, in process design, it is widely used for mediation. Due to the conditioning application, the valve seal is in a throttling state for a long time, and the impurities in the oil wash the seal, damaging the seal.

The process of shell experiments and seal experiments done by turbine fixed ball valves in some artificial environments is as follows. Double blocking and discharge function of turbine fixed ball valve: the turbine ball valve is fixed by using tension spring preload float valve seat, when the valve is in two different states, full open and fully closed, the fluid is ...

Pneumatic butterfly valves are usually composed of a combination of pneumatic actuators and valve bodies and some accessories after debugging. This article first introduces the precautions for the on-site application of pneumatic butterfly valves. 1. The control cabinet sends a signal that the valve does not move, and the pneumatic conditioning butterfly valve is in the device locator after on-site investigation.

The commonly used medium for valve pressure testing is water, oil, air, steam, nitrogen, etc., and the pressure testing methods of various valves are as follows. (1) Globe valve and throttle valve For the strength test of globe valve and throttle valve, the assembled valve is usually placed in the pressure test frame, the valve disc is opened, and the medium is injected into the ...

The basic structure of the centrifugal pump is composed of six parts, namely the impeller, the pump body, the pump shaft, the bearing, the sealing ring, and the stuffing box. 1. The impeller is the core part of the centrifugal pump, its speed is high and the output is large, and the blades on the impeller play a role in the ...

"Pass" and "position" are important concepts of pneumatic reversing solenoid valves. Different "passes" and "positions" constitute different types of pneumatic reversing solenoid valves. Generally speaking, the "two-position valve" and "three-position valve" refer to the valve core of the reversing valve with two or three different operating directions. The so-called "two links" ...