Xinjie touch screen features and advantages

With the continuous development of industrial automation, PLC is widely used in industrial control professions. No matter how strong the PLC product is, it often fails to work normally. All kinds of brands of PLC have the function of self-diagnosis, but the skill of PLC repair is that when the PLC is abnormal, the function should be fully used.

The XDHI XLH series of 16-axis high-performance EtherCAT controllers is the perfect choice for small motion control. Product model XDH-30A16-E/XDH-30A16L-E Small/16-axis type Frequency: 600MHz Program Capacity: ...

1. PLC input and output A small PLC controls a complex system with agility, and what can be seen is the upper and lower rows of staggered input and output relay terminals, corresponding lamps and PLC numbers, just like a piece of integrated electricity without dozens of feet. If any ego doesn't look at reason...

Following the launch of XDH, XLH series 16-axis and other models, Xinjie has achieved good market feedback, and the XLH-30A32 low-profile controller to be launched today can be expanded by 32 bus nodes, and has better performance in basic performance and bus control ability. ...

Product Description: According to the 2.4GHz Wifi wireless communication module, it has RS232 and RS485 interfaces Compatible with Xinjie XC2 - XCM series, XD series PLC, MODBUS RTU equipment The XD-WBOX-ED is connected to the left side of the XD series PLC Opt IEEE802.11b.g. ...

PLC programmable logic manipulators are the core part of industrial control. According to the number of I/O points of PLC, PLC can be divided into three categories: small PLC, medium and large. It is a digitally operated electronic device designed for industrial production. It uses a programmable memory to store programs that execute user-facing ...

We want to make sure that the capacity of the inverter is matched. First of all, according to the nature of the load, the correct type of inverter is selected. The general criterion is what is the nature of the load characteristics with what characteristics of the inverter, the following is mainly for pumps and other equipment to clarify. ...

The Variable-Frequency Drive (VFD) controls the speed and operation of the motor by adjusting the frequency and amplitude of the output voltage. Specifically, the VFD controls the speed of the motor mainly through the following steps: Collecting Input Signals: VFD First ...

Xinjie PLC 丨Communication failure is generally summarized as the following problems: (1) Communication parameters: The communication parameters of Xinjie PLC communication port and peripheral equipment may be inconsistent. (2) Communication line: The connection may be incorrect, or the contact is poor, the user can replace the communication line and try again.

After overhauling and confirming that all connections of the system are correct, power on the relevant modules until the card indicator shows normal. The initiation process of the system after the scheduled repair is as follows: (1) Power supply. Turn on the power supply equipment (including the UPS...)

Motor overload: There is no need to set overload maintenance parameters in frequency conversion. The inverter generally acquiesces to the motor overload maintenance based on the motor power. Generally, it is 1.2 times 60 seconds to report the overload problem. The overload factor is not the same for different frequency converters. ...

Control principle: PLC controls the operation of the servo motor by controlling the servo motor. 1. The PLC sends a pulse signal to the servo motor driver, pay attention to the driver. 2. The servo motor drive according to the ...

The usual inverter motor (hereinafter referred to as VFD) can only regulate the speed of the communication motor, and it can be open-loop or closed-loop, depending on the control method and VFD. This is the traditional V/F mode. The basic concept of servo is accurate, precise and fast positioning. Frequency conversion is servo ...

Make accurate punctuality, read accurate punctuality, and stop accurate punctuality. Watchman number. Range: T600 - T618 (T600, T602, T604...) T618, numbered even) Punctuality. Accurate punctuality ...

The World Economic Forum (Davos Forum) Annual Meeting 2016 will be held in Davos from 20 to 23 this month, with the theme of "Mastering the Fourth Industrial Revolution". ...

1. Power switching and maintenance: There is a circuit breaker in the PLC cabinet, which is connected to the incoming power supply. In addition to making and disconnecting circuits, circuits can also be maintained for short circuits and overloads. Cut off the power supply during repairs. 2. Start and stop control function: The panel of the PLC inverter cabinet is equipped with a man-machine interface, and the inverter start and stop button ...

It is reported that after a comprehensive evaluation by the user expert jury, network users and gongkong, Xinjie's XDM-60T10-E motion control PLC won the "Innovative Product Award" in the 13th annual automation selection activity of gongkong. ...

Xinjie PLC conditions are established, why is the corresponding coil not in place? There are two possible reasons for this: (1) The same coil may be used in multiple places to perform the double coil output, and when the double coil is output, the coil on the rear side will operate first. （2） ...

Model introduction of Xinjie PLC 　　XC series Including XC1 (economy), XC2 (basic), XC3 (standard), XC5 (enhanced), XCM (sport), XCC (high-performance) and their corresponding expansion modules, as well as special analog bodies and other special models. XC series PLC can be ...

Although many relays, timers and counters are often used in the ladder diagram programs used by PLCs, PLC does not have these hardware physically, but uses memory and program programming methods to do logic control and editing, and connects external mechanical devices to make physical devices through output components.