Advantech's IPC power-on has no display for failure and maintenance

1. Advantech's IPC does not appear after powering on

1. When Advantech IPC is turned on, there is a connected alarm sound and the display does not appear, perhaps it is due to poor memory oxidation contact or memory fault, reinsert the memory or replace the memory after power failure. If there is still a warning of connection after the industrial computer is turned on after replacing the memory, consider replacing the industrial motherboard.

2. Advantech's IPC has no output when it is turned on, first confirm whether the IPC is connected to an external capture card or motion control card, if so, remove the external card and then power on for testing.

3. Advantech's industrial computer has no alarm sound and no display of the display, you can first discharge the CMOS, and then boot the test, if there is still no display, it may be that the CPU is not in good contact, reinstall the CPU or replace the CPU after power failure, or there is no display, then consider replacing the industrial motherboard.

2. Maintenance of Advantech's industrial computer after power-on

Advantech's IPC is powered on for maintenance and the power is powered off immediately after powering on. First of all, judge whether the power supply is maintained, remove the power connector from the industrial motherboard, short the green wire and any black wire on the power supply 20pin, if the electric fan rotates normally, the power supply is fine.

1. Advantech's industrial computer motherboard maintenance, perhaps the industrial motherboard has a short circuit or a problem, such as screws or water ingress inside the industrial computer.

2. Power maintenance, there is damage inside the power supply.

3. When connecting the main board of Advantech's industrial computer to the aviation head, it is necessary to pay attention to the positive and negative poles that cannot be reversed.

3. Advantech's industrial computer appears after powering on

1. Advantech's IPC prompts a GRUB error after self-checking, or there may be a cursor shining in the upper left corner, mostly because the main guide record of the IPC system is damaged, and the main guide record needs to be rebuilt.

2. During the blue screen of Advantech's IPC boot, first confirm whether the form of the hard disk is correct, WIN XP is in IDE form, WIN 7 or above can be in IDE or AHCI form, if the form is okay, then reinsert the memory or replace the memory, and consider reinstalling the system if the blue screen is also blue.

3. After the Advantech industrial computer is powered on, go directly to the BIOS, generally if the hard disk is not found, you can check whether the hard disk is loose first, and there is no loose replaceable SATA cable and hard disk.

4. After Advantech's industrial computer enters the system, the USB interface cannot be used, reinstall the USB driver, and reinstall the system in other conditions.

5. Advantech's industrial computer keeps restarting after powering on, you can initialize the BIOS before testing, and if it can't solve the problem, consider replacing the memory and industrial motherboard.

6. If Advantech's IPC boots up normally but the hard disk is reported an error or the hard disk is lost, you can change the hard disk form in the BIOS.

7. After Advantech's industrial computer enters the system, there are spots on the display, and the graphics card can be disabled.

8. If you find that the time is wrong after Advantech's industrial computer enters the system, you can adjust the time first, then turn off the 220V power supply after shutting down, and pause for 2 minutes before powering on. If you can't save the time, first use a multimeter to test the power of the button battery, whether there is a power supply of about 3V, if the power is not enough to replace the battery. If the battery level is normal, but it still cannot be saved at any time, the industrial motherboard circuit may be abnormal.

9. If Advantech IPC has a blue screen, reboot or crash during use, first check the heat dissipation status of the IPC (whether there is any abnormality in the CPU fan and chassis fan), sweep away the similar situation caused by system and software problems, if the problem still exists, you can test whether the hard disk has bad sectors.

Advantech's IPC power-on has no display for failure and maintenance

Advantech's IPC power-on has no display for failure and maintenance

Sections viewed

Contact

working hours