Rorobot BML-20005V[P] Recommended load is 30g

Introduction: Soft Touch/Rorobot Finger F-A7 Features: Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece. If you need to customize the shape of the finger or fingertip, please contact customer service. Finger material can be selected conventional ...

Introduction: iPCU2 has two options: standard iPCU2-SMN and high-speed iPCU2-HMN, the high-speed type has a larger vacuum flow rate and is suitable for high-speed handling conditions. iPCU2 Passive Driver: Compact soft-touch passive actuator. -90~300kPa three-speed adjustable output air pressure range ...

Introduction: Rorobot FM-A5V5/LS1 Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 19mm Safe working air pressure: 120kPa Recommended load: 280g Tare weight: 90g Our customer-centric service ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: Conform to ISO9409-1:2004 (i.e. standard GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market. It is recommended to carry a large load of 20kg Suitable for non-standard gripper combinations ...

Introduction: Rorobot Finger Module FM-A8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixation Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot ACU-MMN Active Driver, ACU-MMN Active Driver--Standard, Mobile Soft Touch Gripper Special Controller, Output Air Pressure -70-120kPa, Manually Adjust the Clamping Force by Knob. Built-in drive air source and battery, can be fully charged without external power supply ...

Introduction: Rorobot Passive Driver PCU2-V, Energetic Passive Driver Features: -80-300kPa digitally adjusts the output air pressure range, suitable for a full range of soft jaws and soft finger drives. Precise adjustment of positive and negative pressure, you can choose to adjust the manual knob ...

Introduction: Rorobot BML-4H18[HAS]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and no ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-15 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Rorobot BMC-3B12[H]/S Product parameters Tare weight: 3.3g Maximum load: 10g External gripping force: 0.1N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 24 ...

Introduction: Rorobot Soft Jaw BMC-3B24[H]/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch material points ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...

Introduction: Soft Touch/Rorobot Finger Module FM-B7V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small space occupation. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot Finger Module B5V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot soft claw B-21413, B-21413, it can grasp the battery, can grasp the screw, can grasp the camera module, can grasp the rod, but also grasp the incense ash, it can be used very well for the outer diameter of 8±8 (mm) workpiece grasping, without changing the fixture on the premise, according to different kinds of work...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-13 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Soft Touch/Rorobot Finger F-A6 Features: Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece. If you need to customize the shape of the finger or fingertip, please contact customer service. Finger material can be selected conventional ...

Introduction: Rorobot Finger Module FM-B5V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BMC-2G1624 [HBAS]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft...