旋转机器人 BMC-4H18[HAS]/S

简介：Rorobot 手指模组 FM-A5V1，特点及适用场景：双指模组组合，结构紧凑，占地面积小。间距和安装角度不可调，适用于夹持微小、轻薄工件，固定方式：可从三个方向固定。 特征： ...

简介：Rorobot 紧凑型有源驱动器 ACU2-B 使驱动器更简单、即插即用、小巧方便，是唤醒桌面机械臂的**佳 cp 产品参数 额定功率：18W 工作电压：24V 输出气压：-85—100kPa ...

Introduction: Rorobot Finger Module FMA7-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: FlexTouch/Rorobot Flange Connection Module FCM-R04 Features: It conforms to the ISO9409-1:2004 standard (i.e., the national standard GB/T 14468.1-2006/), and is suitable for most robot flanges on the market. Lightweight for lightweight articulated machines ...

Introduction: Rorobot BML-20301[H]/S Product parameters Tare weight: 3.5g Maximum load: 30g External gripping force: 0.3N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 1 ...

Introduction: Rorobot BML-4G64[HAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into regular [H] and non-...

Introduction: SoftTouch/Rorobot Connection Module CM-S04 Features: A full range of soft beak modules can be installed at the end Can be mounted on the Flexible Series Slip Mounting Plate [SMP] page.50 Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products...

Introduction: Soft Touch/Rorobot Finger Module B3V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the trachea arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Finger Module FM-A4V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small space occupation. The spacing and installation angle are not adjustable, and it is suitable for clamping small, light and thin workpieces. Features: Features and applicable scenarios: ...

Introduction: Rorobot BMC-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot BML-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot Finger Module C4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Soft Beak B-4B Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Specifications ...

Introduction: Rorobot Soft Beak B-20006 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Products...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: It conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. The maximum load is recommended 20 kg Suitable for non-standard clamps ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...

Introduction: Rorobot BML-3C12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot B-4B30[H]/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch materials are divided into ...

Introduction: Soft Touch/Rorobot Finger F-B5 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot BMC-3B14/S 　　Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...