Embedded IPC installation method - EVOC

(1) Skill characteristics of IPC: 1. The all-tempered industrial chassis that meets the "EIA" specification is selected to enhance the ability to resist electromagnetic disturbances. 2. Select bus structure and modular planning skills. The CPU and each function module all use a plug-in structure, and there is a rubber bead to confirm, which improves the ...

Serial port is a very common device communication protocol on industrial motherboards, and most industrial motherboards contain more than two serial ports based on RS-232. The serial port sends and receives bytes on a bit-by-bit basis, which is slower than parallel communication on a byte-by-byte basis, but the serial port can be used in the use of a single wire.

Many of the problems that may arise from the failure of the industrial computer of the CNC cutting machine are caused by the working environment, and the common ones are as follows: 1. The industrial computer has a long working time. Due to the demand for normal production, some factories ...

1. After the IPC is turned on, the motherboard self-test is successful, but the system cannot be booted from the hard disk 1. Press the "Del" key to enter the CMOS hard disk parameter setting and boot order to see if the boot order is correct. 2. After booting with optical drive or floppy drive, check whether the hard disk of the industrial computer has a boot system or whether the hard disk is normal.

GPIO=General Purpose Input Output. GPIO port is a more important concept, users can interact with the hardware through the GPIO port (such as UART), manipulate hardware operations (such as LED, buzzer, etc.), read hardware operation status signals (such as ...

(1) The chip part of the industrial control motherboard 　　BIOS chip: The basic input and output system programs of the motherboard are all in the BIOS. It allows the motherboard to recognize each piece of hardware, and you can also set the boot system device and adjust the external frequency of the CPU. Southbridge chip: The location is on top of the PCI slot ...

On November 8th, the 2017 (6th) Global Automation and Production Theme Summit, co-sponsored by the internationally renowned industrial media CONTROL ENGINEERING China and PLANT ENGINEERING China (referred to as CEC and PEC), was grandly held at Howard Johnson Kinguyuan Hotel in Shanghai.

PC (personal computer) is derived from IBM's first desktop computer type, PC, in 1978, which is a personal computer that can run independently and perform specific functions. Personal computers do not need to share resources such as processing, disks, and printers from other computers ...

1. Why can't resistive touch screen achieve multi-touch control in the same way as capacitive touch screen? Resistive touch screens do not allow for multi-touch, which is due to their structural resolution. The resistive touch screen is divided into two layers, separated by a barrier in the center. When touching the touch screen of an industrial tablet, the two-layer ...

PLC programmable logic manipulator: It is mainly composed of CPU module, input module, output module and programming equipment. DCS distributed control system: It is mainly a multi-level computer system composed of process control level and process monitoring level with communication network as the link, which summarizes the computer ...

When selecting a high-speed data acquisition card, the following goals are generally considered: Sample rate, resolution, number of channels, bus, etc. The selection of the key depends on what your high-speed data acquisition card is for, so as not to blindly select the data acquisition card. Because different data acquisition cards are used in different places ...

The industrial computer chassis is an important part of the industrial computer, which is related to whether the industrial computer can work normally, so what elements will affect the function of the industrial computer chassis? 1. Thermal conductivity elements The rationality of the heat dissipation structure is related to whether the industrial computer can ...

Detection method and sequence of industrial computer failure not starting: 1. Check the three major operating conditions of the CPU Power supply clock reposition 2. Remove the BIOS and check whether the 22-pin chip selection signal has jumped 3. Try changing the BIOS and check the line connected to the BIOS 4 ...

Example: When the system is turned off, the IPC displays an error message of "insufficient memory". Once you click on the "Confirm" button, the blue screen issue is presented again. Out of memory (Out of memory) Problem description: A quad-core industrial computer starts to operate normally, but runs a ...

依据运用用途，主板可分为工业主板与商用主板两大类。商用主板首要面向家用及办公电脑运用，工业主板首要面向工业场合运用，故工业主板与商用主板在规划上有较大的不同。 ...

1. It can be powered on but not lit 1. There is no alarm sound display of Didi when booted, maybe it is poor contact of memory oxidation or there is a problem with the memory itself, the solution is to wipe the memory with an eraser and reinsert it back after power-off, and replace the memory with its own problem.

With the development of a new generation of information technology such as artificial intelligence, big data, and the Internet of Things, the industrial control system has begun to develop in the direction of intelligence, networking, and digitalization. Embedded industrial computer is a major development in recent years.

With the continuous development of industrial computer technology, industrial computers have been widely used in industrial production. Therefore, we need to understand the causes of industrial computer failures and how to deal with them. Below, we give corresponding solutions to the common faults of industrial computers. ...

The M90 Edge Computing Unit is a brand new product from EVOC. It adopts the principle of embedded design and is equipped with an AI accelerator card. Designed for artificial intelligence and edge computing such as intelligent detection, industrial control and detection, environmental monitoring, behavior analysis, machine vision, and assisted driving. It can be done on the edge ...

The ambient humidity is not suitable. The industrial computer is mainly composed of integrated circuits of many electronic components, and its insulation function is greatly related to the ambient humidity. If the humidity is too high, it is easy to form a short circuit and burn the circuit board; If the humidity is too small, it is easy to generate static electricity, and it will also break down some electronic components.