Kunlun Tongtai touch screen - common faults and fault analysis of resistive screens

1. Click the "Settings" button on the MCGS interface to enter the settings interface. 2. Click on the "Alarm Answer" tab. 3. In the Alarm Response tab, check the Enable Alarm Response box, and set the Answer Time, Trigger Alarm Time Range, Response Time, Response Time, Alarm Response, Alarm Response, Alarm Response, Alarm Response, Alarm Response, Alarm Response,

1. The film surface of the touch screen is the touch surface, that is, the front of the product; The glass side is non-touch, i.e. the back of the product 2. The touch screen part is a glass product, the corners of the glass are sharp, please wear gloves/finger sleeves when assembling 3. The touch screen part is a fragile glass product, and it should not be touched during assembly.

Inaccurate screen position: Repositioning can be done via driver software. Touch position and screen cursor upside down: When installing the touch screen, the position of the screen is reversed, please adjust the touch screen position according to the principle of right-hand position out. The touchscreen display icon keeps pointing towards the fixed ...

Four-wire touch screen The four-wire touchscreen contains two resistive layers. One of the layers has a vertical bus on the left and right edges of the screen, and the other layer has a horizontal bus at the bottom and top of the screen, see Figure 1. In order to measure in the X-axis direction, the left side of the bus is offset to 0V, and the right side ...

81. What are the main characteristics of 128M TPC? (1) CE platform upgrade Using WINCE 5.0 operating system, user operation methods and habits are the same as those of the previous CE 4.2 system; (2) Hardware storage device upgrade The total storage data capacity of the product has increased from the existing 6 ...

1. Touch screen (touchscreen), also known as "touch screen" and "touch panel", is an inductive liquid crystal display device that can receive input signals such as contacts.

56. Does TPC support OPC communication? No, the network version supports OPC communication. 57. 200PLCLC communication wiring with TPC7062K (1) The 7 positive and 8 negative of the TPC RS485 interface is connected with the positive and 8 negative of the PLC serial port 3, and the wiring diagram is as follows: TPC PLC 58. 200 ...

1. The capacitive touch screen only needs to touch, and no pressure is needed to generate a signal. 2. Capacitive touch screen only needs to be corrected once or not at all after production, while resistive technology requires conventional correction. 3. The life of the capacitive solution will be longer, because the part in the capacitive touch screen ...

1. Connect the touch screen with the PLC We know the communication between two pieces of hardware, whether wireless or wired. The first step is to establish a connection. The most common connection between PLC and touch screen is serial data cable connection. The data cable can be used in a treasure ...

1. Do not hit with metal objects. Usually the HMI will be covered with a layer of glass to protect the screen and make it easy to touch. However, the glass is fragile, do not hit the screen with metal objects during use, it is easy to cause the glass to be scratched or broken. 2. Avoid squeezing the screen with heavy objects. Around HMI ...

31. Historical alarms are not displayed (1) "Automatically save the generated alarm information" is not selected in the attribute setting of the alarm data object; (2) The alarm data does not reach the upper/lower limit of the alarm value; (3) "MCGS_ALARM" is not selected for the group object. 32. ...

1. The optical performance is the best. The clarity and light transmittance are the highest, the reflection is the least, and there is no color distortion, this is because the sound wave screen body is pure glass, unlike the resistive screen with multiple layers of composite film; The capacitive screen is coated with a layer of film on the surface, and the light transmittance is worse. 2. Anti-scratch and anti-barbaric use ...

1. If you are using a capacitive touch screen, then it is recommended that you first install the driver required for the capacitive touch screen correctly according to the requirements of the manual when you use it for the first time, and then click "Start" / "Programs" / "Microtouch" on the screen with your fingers.

One. The touch screen is not allowed Fault phenomenon: A surface acoustic wave touch screen, touching the part of the monitor screen with your finger can not complete the corresponding operation normally. Fault analysis and processing This phenomenon may be the reflection of the sound wave touch screen around the screen after a period of use.

20. The TPC project running environment is automatically restarted If the CPU usage reaches 99% during the project runtime, the runtime environment will automatically exit and then restart. There may be many reasons for high CPU usage: too many bitmaps, too many scripts in the loop policy, and short cycle times. ...

61. 200PLC: What is the reason for the communication status jump (1) Whether the communication delay setting is too short, and set the appropriate delay time; (2) Whether there is interference on site, shielded wire and grounding can be used; (3) Refer to PLC "SMW22", see PLC running program ...

47. There are very few drivers in Device Manager (1) Whether to select "All Driver Installation" when configuring the software installation, if not, you need to reinstall the driver; (2) If you don't find a supported driver in the device window of the configuration software, check whether the device supports the standard ...

1. Variables in the real-time runtime cannot add channels and send data using functions at the same time. 2. In the universal serial port parent device, the COM port indicates whether to select 232 or 485, and in the touch COM1 indicates the 232 interface, and COM2 represents the 485 interface. 3. View the touch ...

1. Prepare a USB flash drive of 8GB or less. Insert the USB port behind the touch screen, restart the touch screen, and quickly tap the progress bar when the process progress bar appears on the touch screen screen. 2. Click "System Maintenance". 3. Click Back up System Information. 4. Make sure the display path is us...

In May, ten seminars in East China and North China had just ended, and in June, Kunlun Tongtai attacked again, continuing the enthusiasm of Red May to June. The sky is blue and the clouds are white, and the Kunlun Tongguo Seminar (Beijing) Shunyi special session opened. On June 12, 2015, Kunlun Tongtai 2015 Seminar - Beijing