Industrial computer hard disk class failure - EVOC

After the IPC is infected by viruses or hackers, the engine area of the hard disk may be damaged, or the hard disk or partition may be lost. This problem is usually caused by hackers or viruses correcting the boot area of the hard drive or encrypting the partition table or moving the sectors of the boot area. ...

Memory is one of the most important components in industrial motherboards, which is mainly used to temporarily store the computing data in the CPU and the data exchanged by external memory. In the operation of industrial computers, there may be incompatibility between memory and industrial motherboards. The following is an introduction to the incompatibility of memory with industrial motherboards ...

Serial port is a very common device communication protocol on industrial motherboards, and most industrial motherboards contain more than two serial ports based on RS-232. The serial port sends and receives bytes on a bit-by-bit basis, which is slower than parallel communication on a byte-by-byte basis, but the serial port can be used in the use of a single wire.

1. Scale The industrial motherboard can be directly installed in the equipment for use, such as being installed in the active vending machine to achieve active vending; It can be used in traditional 4U industrial computer chassis, which is often used in machine vision, industrial automation and other fields; Or it can be installed in the embedded host, suitable for VTM, subway ...

With the modernization, high-tech and sophistication of electronic equipment, it is necessary to rely on an automatic testing system to complete the on-site rapid testing of electronic equipment. The radar automatic test system is based on the "PCI bus test software channel", aiming at the needs of the radar machine test.

1. Turn on the power of the computer and the computer does not respond: 1. Check whether the power socket has power and is normally connected to the computer; 2. Check whether the computer power supply can work normally (whether the power fan rotates after turning on), and whether the display is connected to the host normally; 3. Turn over the machine ...

The traditional industrial computer uses a combination of 4U and other types of cold-rolled plate chassis + gold finger motherboard (full-length or half-length card) + base plate + high-power power supply. There are a number of unstable elements to such a structure: 1. If the CPU card is inserted into the baseboard, there will be a bad touch phenomenon, such as vibration.

Downtime is a common fault of the industrial computer, and the ability to solve the downtime can ensure the high reliability and real-time function of the industrial computer. The following is an analysis of the common causes and solutions of industrial computer downtime. 1. Too much dust causes downtime ...

The M90 Edge Computing Unit is a brand new product from EVOC. It adopts the principle of embedded design and is equipped with an AI accelerator card. Designed for artificial intelligence and edge computing such as intelligent detection, industrial control and detection, environmental monitoring, behavior analysis, machine vision, and assisted driving. It can be done on the edge ...

Compared with traditional PC computers, industrial computers are more used in harsh environments, so industrial computers have more and more stringent requirements in terms of easy maintenance, heat dissipation, dustproof, product cycle, size, etc., therefore, it has created the unique characteristics of industrial computers. ...

1. After the IPC is turned on, the motherboard self-test is successful, but the system cannot be booted from the hard disk 1. Press the "Del" key to enter the CMOS hard disk parameter setting and boot order to see if the boot order is correct. 2. After booting with optical drive or floppy drive, check whether the hard disk of the industrial computer has a boot system or whether the hard disk is normal.

1. Device operation system First: Review the settings in the CMOS and restore to factory settings if needed. Secondly: pay attention to the parameters of the hard disk, the temperature of the CPU, etc. Observe whether the information displayed during the self-test of the industrial computer is consistent with the actual hardware equipment. 2. Device software ...

EVOC IPC troubleshooting is eight before and eight after 1. Investigate first and then familiarize: first consider where the problem may be according to the analysis of the on-site situation, and then do the operation; 2. Clean first and then overhaul: Practice shows that many faults ...

Industrial tablet PC is a kind of industrial computer, which is an all-in-one structure, and the host, liquid crystal display, and contact screen are integrated. It has the characteristics of contact function, consolidation, vibration prevention, wide temperature, rich I/O interface, etc., which makes it more convenient and fast to communicate, communicate, input and accept information between the user and the machine.

1. Why can't resistive touch screen achieve multi-touch control in the same way as capacitive touch screen? Resistive touch screens do not allow for multi-touch, which is due to their structural resolution. The resistive touch screen is divided into two layers, separated by a barrier in the center. When touching the touch screen of an industrial tablet, the two-layer ...

Example: When the system is turned off, the IPC displays an error message of "insufficient memory". Once you click on the "Confirm" button, the blue screen issue is presented again. Out of memory (Out of memory) Problem description: A quad-core industrial computer starts to operate normally, but runs a ...

In the process of using the industrial computer, the user mistakenly deleted the system file, resulting in an abnormal function of the industrial computer; The industrial computer was invaded by a virus Trojan, resulting in problems in the system; Some fault prompts frequently pop up on the desktop, and the industrial computer needs to be reinstalled in the system. Strictly speaking, the industrial computer presents ...

Industrial motherboard is a motherboard used in industrial occasions, which is selected by industrial computers, and can adapt to wide temperature environments, harsh environments, and long-term high-load work according to needs. When choosing an industrial motherboard, you need to consider the following questions: Plate type ...

The ambient humidity is not suitable. The industrial computer is mainly composed of integrated circuits of many electronic components, and its insulation function is greatly related to the ambient humidity. If the humidity is too high, it is easy to form a short circuit and burn the circuit board; If the humidity is too small, it is easy to generate static electricity, and it will also break down some electronic components.

If you are sure to use Advantech's industrial computer, then you must understand whether you need Advantech's original machine or a dealer's assembly machine. Taiwan industrial computer in the early stage of entering the domestic market did not have the original machine, that is, the chassis and motherboard, the rest are assembled by dealers. Later, there was the original ...