Industrial computer motherboard failure and solution——EVOC

System Applications 1. Embedded Computers: 19-inch upper frame standard construction, NEMA 4/12 aluminum alloy waterproof and dustproof front panel; 10.4-inch TFT color LCD display with EVOC P3 embedded computer motherboard; 2. Servo control serial communication card, six ...

Heat sinks are one of the top sources of noise in industrial computers. The more advanced and newer the industrial computer, the more complex the internal processor structure and the greater the heating. Therefore, the rationality of the heat sink design is related to whether the industrial computer can operate stably. We all know that the internal hardware of industrial computers ...

First of all, the biggest difference between industrial control motherboards and general PC boards is that there are more PCI slots on industrial motherboards, some of which are ISA slots. PC boards don't usually do this. Usually, industrial control motherboards do not have graphics cards. There is a PCI-E graphics slot on the computer motherboard. In addition to embedded ...

The industrial computer, that is, the industrial computer, the primary structure and operating principle are the same as that of ordinary computers, the difference is that the industrial computer adopts a steel structure chassis, with fixed strips inside, and has a high anti-magnetic, dust-proof and anti-oscillation ability, which is suitable for complex industrial sites. The IPC can be used for data receiving.

The temperature is not suitable for the maintenance of the hard drive, if the case temperature reaches 30 degrees Celsius, the temperature of the internal hard drive will reach 40 degrees or higher. We can briefly DIR our industrial computer to achieve the effect of reducing the ambient temperature. 1. Replace high-power CPU and hard disk fan (hard disk fan to...

The industrial control motherboard is an important part of the industrial computer, which can get used to the messy environment and long-term high-load work on the industrial site. The differences from commercial motherboards are: First, the materials and planning of components Commercial motherboards ...

If you are sure to use Advantech's industrial computer, then you must understand whether you need Advantech's original machine or a dealer's assembly machine. Taiwan industrial computer in the early stage of entering the domestic market did not have the original machine, that is, the chassis and motherboard, the rest are assembled by dealers. Later, there was the original ...

1. First place the body of the embedded industrial control all-in-one machine in a stable place, and accurately embed the base into the body. 2. Put on the screws, screw the screws into each eyelet, and confirm whether they are tightened. 3. Before cleaning the screen of the embedded industrial control all-in-one, stop using the equipment and unplug the power plug.

A general-purpose server that is responsible for receiving, processing, and processing large amounts of data is of great importance to users. Through repeated optimization and multiple tests, we finally won the first battle, and EIS-2209-FT made its debut in the C position! 22 ...

Industrial computer virus refers to a set of instructions or program code that can affect the normal operation of the machine and reproduce itself through some unconventional means, which has several important characteristics of propagation, concealment, destruction and infection. What will happen to the virus in the industrial computer?

There are generally two types: embedded motherboards based on x86 ARM embedded motherboards based on RISC (Reduced Instruction Set Computers), also known as ARM embedded motherboards (licensed by ARM, each chip manufacturer has its own special functions). ...

1、0x0000007E There are many reasons for this, including hardware compatibility, faulty drivers or system services, or some software. Solution: Use the Event Viewer to get more information and discover the source of the fault. ...

Serial port is a very common device communication protocol on industrial motherboards, and most industrial motherboards contain more than two serial ports based on RS-232. The serial port sends and receives bytes on a bit-by-bit basis, which is slower than parallel communication on a byte-by-byte basis, but the serial port can be used in the use of a single wire.

After a period of use, the industrial touch all-in-one computer will have problems such as dirty display or internal dust. That's where cleaning comes in. If the cleaning is not timely, it will lead to problems such as contact failure, system software failure, and system software echo. However, if the cleaning method is not right, ...

During the use of the industrial computer, the user mistakenly deleted the system file, resulting in an abnormal function of the industrial computer; The industrial computer was invaded by viruses and Trojans, resulting in system problems; Some fault prompts frequently pop up on the desktop, and the industrial computer needs to be reinstalled in the system. Strictly speaking, the industrial computer presents ...

EVOC MCA solutions - computer skills, mobile computing skills, Internet of Things skills, handwriting input skills, wireless connection skills, and video, RFID, fingerprint, barcode and other product skills, intelligent medical. Schematic diagram of EVOC MCA solution ...

When selecting industrial computers, we often encounter PCI and PCI-e expansion slots, what are the differences between the two? 1. The color is different. In IPC motherboards, the PCI slot is milky white, while the PCI-e slot is black. 2. The transmission rate is different. PCI slot max data ...

The LED die bonder is generally faced with a moving PCB board, and the LED wafer is sucked from the wafer tray and mounted onto the movable PCB (printed circuit board), which is particularly important for the matching and coordination of the machine, so it brings strict requirements to the action time and processing speed of each part of the system; Combine...

1. Device operation system First: Review the settings in the CMOS and restore to factory settings if needed. Secondly: pay attention to the parameters of the hard disk, the temperature of the CPU, etc. Observe whether the information displayed during the self-test of the industrial computer is consistent with the actual hardware equipment. 2. Device software ...

An important part of a motherboard can be said to be the chipset of the motherboard, the chipset of the motherboard is usually composed of a northbridge chip and a southbridge chip, and the two together form the chipset of the motherboard. Northbridge Chip is primarily responsible for the completion of the work with the CP ...