FlexTouch/Rorobot Flange Connection Module FCM-R02

Introduction: Rorobot Soft Jaw BMC-20802 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Rorobot Finger Module FMA6-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot module B-4A30/M is a slender soft claw, suitable for jelly shells, test tubes, badminton, cylindrical, hollow columns and other fragile and fragile objects of non-destructive internal support handling and sorting, to ensure that the product will not be scratched, reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: Rorobot Finger Module A7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction:Rorobot Robot Soft Gripper BMC-20005V, B-20005V/S can be used well for 0.18mm-3mm between small and light and thin special-shaped workpieces, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot FM-C4V5/LS1 Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 9mm Safe working air pressure: 120kPa Recommended load: 145g Tare weight: 28g Our customer-centric service philosophy ...

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft jaw material is divided into conventional type, when the weight of the workpiece ...

　　Introduction: Rorobot B-3B10[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and ...

Introduction: Rorobot B-20005V Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Products...

Introduction: Soft-Touch/Rorobot Skid Shift Mounting Plate SMP-5S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module C7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: It conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. The maximum load is recommended 20 kg Suitable for non-standard clamps ...

Introduction: Rorobot Finger Module B7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot BMC-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot Finger Module C8V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: FlexTouch/Rorobot Spring Rod Flange Connection Module FCM-S01 Features: In line with the ISO9409.1:2004 standard (i.e. GB / T 14468-2006/), suitable for most of the robot flanges on the market For mounting soft beak modules or light hand claws ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LP]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. The soft claw material is divided into ...

Introduction: Rorobot Soft Jaw BMC-4G64[HAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Finger Module B6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module A4V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.