Soft Touch/Rorobot Finger F-B3 Negative Pressure Stroke 10mm

Introduction: Rorobot BMC-4H18[HAS]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and no ...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot soft beak module BM series can be installed in the connection module [CM] or flange connection module [FCM]; The soft beak module comprises a soft beak and a matching fitting joint; The module assembly is supplied with a straight-through fitting fitting (PN-066) or a side-through fitting fitting (PN-007); Soft beak ...

Introduction: Rorobot soft jaw BML-3A18[H]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the clamping fingertip distance G and the external support fingertip distance D can be ...

Introduction: Soft-Touch/Rorobot Actuator LCH-U is a lightweight actuator designed for soft-touch grippers with both positive pressure and vacuum output, and can be used for both multi-channel and asynchronous drives Product parameters Enter the air supply 0.4—0.6MPa Flow rate> 200L/min Lose...

Introduction: Rorobot Finger Module B6V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Soft Touch/Rorobot Finger Module FM-A3V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) . ...

Introduction:Rorobot FM-C4V5/LS1[HAS] Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 3mm Safe working air pressure: 300kPa Recommended load: 70g Self-weight: 20g Our customer-centric service ...

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft jaw material is divided into conventional type, when the weight of the workpiece ...

Introduction: Rorobot Finger Module FM-C7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot FM-C4V5/LS1 Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 9mm Safe working air pressure: 120kPa Recommended load: 145g Tare weight: 28g Our customer-centric service philosophy ...

Introduction: Rorobot Soft Beak B-3B18 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Product References ...

Introduction: Rorobot BMC-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot Finger Module A4V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot ACU-MMN Active Driver, ACU-MMN Active Driver--Standard, Mobile Soft Touch Gripper Special Controller, Output Air Pressure -70-120kPa, Manually Adjust the Clamping Force by Knob. Built-in drive air source and battery, can be fully charged without external power supply ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LP]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. The soft claw material is divided into ...

Introduction: Rorobot Finger Module B4V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

　　Introduction: Rorobot B-3B10[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and ...

Introduction: Rorobot B-4B50/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch materials are divided into conventional ...

Introduction: Rorobot Finger Module FMA8-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...