Rorobot BML-3A18[HAS]/S The recommended load is 30g

Introduction: Rorobot Finger Module A7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction:Rorobot FM-C4V5/LS1[HAS] Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 16mm Safe working air pressure: 300kPa Suggested load: 380g Tare weight: 90g Our customer-centric ...

Introduction: Rorobot Finger Module C8V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the installation module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger F-C3 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot Finger Module A3V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Soft Touch/Rorobot Finger Module FMA5-V3 Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot BML-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot B-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H] and non-marking type [ ...

Introduction: Rorobot Finger Module FM-B6V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot soft jaw BMC-3A18 [HAS]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the fingertip distance of the clamping fingertip G and the external support fingertip distance is D...

Introduction:Rorobot Robot Soft Jaw BML-20201[HAS]/S,B-20005V/S can be well used for small, light and thin special-shaped workpieces between 0.18mm-3mm, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, blanking accuracy ...

Introduction: Rorobot BMC-3B12[H]/S Product parameters Tare weight: 3.3g Maximum load: 10g External gripping force: 0.1N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 24 ...

Introduction: Soft Touch/Rorobot Finger F-A7 Features: Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece. If you need to customize the shape of the finger or fingertip, please contact customer service. Finger material can be selected conventional ...

Introduction: Rorobot Finger Module C6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft-Touch/Rorobot Slip Mounting Plate SMP-2S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: The multi-finger opposite hand claw has a large grasping strength, can be grasped in both directions by standing and lying down, has strong adaptability, and can perfectly solve the problems of shaking and positioning deviation when grabbing hanging parts. The soft material and adjustable grip force eliminate scratches and damages on the surface of the product. Aluminium profile frame, ...

Introduction: SoftTouch/Rorobot Connection Module CM-S04 Features: A full range of soft beak modules can be installed at the end Can be mounted on the Flexible Series Slip Mounting Plate [SMP] page.50 Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products...

Introduction: Rorobot Soft Jaw BML-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-13 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction:Rorobot Robot BMC-2G1211[HAS] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] ...