P+F proximity switches are indicated by letters

The servo press drives the fine ball shaft through the synchronous belt to complete the accurate orientation control of the pressure spindle, and the high-sensitivity pressure sensor equipment is at the front end of the pressure spindle, which can detect the load of the pressure spindle in real time. Real-time collection of orientation and load data to complete the fine ...

1) It is recommended to place the pressure sensor and its tee valve at the level of the axillary line, which is used for ventilation and sensor zeroing. 2) Approve the maintenance cap on the three-way valve to be perforated, connect the sensor with the monitor, and follow the instructions of the monitor to ...

As one of the early participants and drafters of Industry 4.0z in Germany, we were involved in the discussion of the RAMI reference architecture model. Focusing on connectivity and data presentation, through exhibitions and market applications, we have achieved relevant results, collected effective feedback, and guided our digital and physical products.

The motor control loop is mainly composed of a motor, a controller, and a directional response interface. The motor rolls the rotating shaft and drives the robotic arm to move. The motor manipulator controls when the motor applies force, stops, or continues to roll. The azimuth interface in the loop supplies the rotational speed and azimuth information to the controller ...

First, pay attention to the capacitive and inductive resistance of cables and field equipment, explosion-proof is the system explosion-proof, in addition to the need for P+F safety barriers to reach the required explosion-proof level, the energy storage of cables and field equipment is also a key issue. Especially after the parametric certification replaces the system certification, the engineering company has a special ...

An encoder is a device that converts angular or linear displacement into an electrical signal. The former becomes the yardstick, and the latter is called the yardstick. According to the readout method, the encoder can be divided into two types: touch type and non-touch type. The touch type selects the brush output, and a brush touches the conductive area or the insulating area to represent the shape of the code.

The dry contact of the barrier is an electrical switch that has two positions: closed and disconnected. There is no polarity between the two contacts of the dry contact and is interchangeable. That is, a simple switch, the contact does not provide power supply, and the power supply can be used to control the condition of the equipment. But it doesn't offer ...

Strain gauge tension and compression load cells are available in two different input and output wiring methods: The first is the four-wire connection method. The load cell of the four-wire connection method has no special requirements for the secondary instrument panel, and it is very convenient to use, but when the cable is long, it is easy to be shaken by the operating temperature.

1. Selection of reliability The potential of a sensor to persist in its properties over a period of time is called reliability. In addition to its own structure, the key factor affecting the long-term reliability of the controller is the use of harsh environments. Evil...

In many applications, there are certain safety requirements not only for the sensors in use, but also for the sensor cables. In order to ensure that the adapter components also meet these requirements, the new cable maintenance system provides the ambition for sensor adapters, cable conduits and cable glands ...

A sensor is an input device that receives a signal or stimulus and responds to it. Some sensors now integrate many sensing elements and readout circuitry into a single silicon chip, which then provides high accuracy and multiple functions. The new sensor has more functions, including user friendliness.

Torque sensor is a sensor widely used in the mechanical category, which can measure the torque of rotating objects, and torque sensors have a wide range of application scenarios, and several typical application scenarios will be introduced below. First of all, the short-term sensor is widely used in the automotive industry to measure the engine and transmission.

Because the appearance of the six-wire sensor and the six-wire four-wire sensor can not be distinguished, before the measurement and verification personnel test the sensor, if they find that the sensor input and output cable has six wires, it should be clear whether the sensor is a six-wire sensor, and the six-wire load cell test can not use a fine digital voltmeter...

An important function of the photoelectric switch is to be able to handle changes in the intensity of light: the light beam is changed by using optical components in the transmission medium; Use a beam of light to reflect objects; Instantaneously returns the light emitted by the beam over a long distance. 　　The photoelectric switch (photoelectric sensor) is a photoelectric proximity on...

In the early application and selection of sensors, how to choose is a very important point, and the selection is smooth, and the following will briefly talk about how the sensor is selected in the early stage. The use of the sensor in practical operation is relatively common and may be practical ...

The pulse encoder is a rotary encoder that uses the rotation pulse for signal output, and the main characteristics are the standard shape and diversified shape structure; The internal coding is stable, the signal output qiang, and the pulse value and positioning value are clear. Therefore, when choosing this type of punching encoder, ...

There are two types of accelerometers: one is the angular accelerometer, which is improved from gyroscopes. The other is a linear accelerometer. It can also be divided into single-axis, dual-axis and three-axis accelerometers according to the measurement axis. At the moment, accelerometers are widely used in game controls.

The premise of load cell replacement is that the axis of the applied force coincides with the axis of the sensor, we should know one thing, that is, with the increase of the additional load, the microvolt/indexing signal output by the sensor decreases. About the electromechanical junction of the S-shaped sensor installed in the second force transmission link ...

Instructions for setting up the ultrasonic function: The LED shows the setup process. The green light flashes and the target is found; The target did not notice a red ED flash; The connection setting is tucked into place and the T is set. Once the setup process is complete, the sensor works normally. ...

PRT (Pulse Ranging Technology) stands for Pulse Ranging Technology, which is currently the most accurate industrial-grade process used to measure intervals. By using this direct measurement method, the measurement range from a few centimeters to several hundred meters can be accurately recorded. ...