Rorobot BML-3A18[H]/S The recommended load is 30g

Introduction: Rorobot BML-4G64[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module A7V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Robot Soft Jaw BML-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction: Rorobot BMC-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and non-marking ...

Introduction: Rorobot Finger Module FM-C8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module B8V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Use Screw Accessory Kit PK) and Simplify Tubing Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot BMC-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot Finger Module A4V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Finger Module FM-B4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction:Rorobot Soft Jaw BML-20606, Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot Soft Gripper BMC-4G64[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module A6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Flange Connection Module FCM-R08 Features: Conform to ISO9409-1:2004 (i.e. standard GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market. It is recommended to carry a large load of 20kg Suitable for non-standard gripper combinations ...

Introduction: iPCU2 has two options: standard iPCU2-SMN and high-speed iPCU2-HMN, the high-speed type has a larger vacuum flow rate and is suitable for high-speed handling conditions. iPCU2 Passive Driver: Compact soft-touch passive actuator. -90~300kPa three-speed adjustable output air pressure range ...

Introduction:Rorobot Robot BMC-2G1211[H] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] and ...

Introduction: Rorobot Finger Module FMA8-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction:Rorobot Robot BMC-2G1211[HAS] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot Soft Beak B-3B18 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Product References ...

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module FM-A6V2, Features and Applicable Scenarios: Independent Installation, Can be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixation Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...