Soft Touch/Rorobot Finger Module FM-A6V2 Finger length 83mm

Introduction: Rorobot FM-A5V5/LS1 Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 19mm Safe working air pressure: 120kPa Recommended load: 280g Tare weight: 90g Our customer-centric service ...

Introduction: Rorobot BML-4H18[HAS]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and no ...

Introduction: Rorobot Finger Module FM-B5V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot Finger Module C8V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the installation module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger Module C7V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Use Screw Accessory Kit PK) and Simplify the Trachea Arrangement. It is mostly used in scenarios where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm Features: ...

Introduction: Rorobot BMC-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction: Rorobot Soft Beak B-20008 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Products...

Introduction: Rorobot Finger Module B5V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LP]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. The soft claw material is divided into ...

Introduction: Rorobot Finger Module A7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: SoftTouch/Rorobot Connectivity Module CM Series Features: A full range of soft beak modules can be installed at the end Can be mounted on the soft beak series sliding mounting plate [SMP]. Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products layered grabbing ...

Introduction: Soft Touch/Rorobot Finger Module A8V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Soft Jaw BMC-1G364030[HAS]/M, is a strengthened version of the single finger soft jaw, the recommended fingertip and workpiece distance is (19-28) mm, the recommended load of one finger soft jaw is (0-500) G, and the external gripping clamping force is (0-11) N. Features: Positive pressure state fingertips ...

Introduction: Rorobot BMC-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot Finger Module B8V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Use Screw Accessory Kit PK) and Simplify Tubing Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Soft Touch/Rorobot Independent Finger Module SMP-03 Features: According to the length of the slot, it is divided into SMP-01 / SMP-02 / SMP-03 It can be used for the assembly between the finger module [FM] and the aluminum profile The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Soft-Touch/Rorobot Skid Mounting Plate SMP-3S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot BML-2G1624[HB]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft claws ...

Introduction:Rorobot Robot Soft Jaw BML-20201[HAS]/S,B-20005V/S can be well used for small, light and thin special-shaped workpieces between 0.18mm-3mm, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, blanking accuracy ...

Introduction: The multi-finger opposite hand claw has a large grasping strength, can be grasped in both directions by standing and lying down, has strong adaptability, and can perfectly solve the problems of shaking and positioning deviation when grabbing hanging parts. The soft material and adjustable grip force eliminate scratches and damages on the surface of the product. Aluminium profile frame, ...