Introduction to the application of Omron micro switches

Process introduction In the traditional die-cutting process, because the cutter cannot cut the material completely, the connecting frame will be left, which increases the cost of the material. In addition, the service life of the die-cutting knife is 1 million times, such as long-term continuous operation, it needs to be replaced and maintained in time, and the maintenance and debugging time is also very long.

How it works Add a certain voltage at both ends of the coil, a certain current will flow through the coil, thus producing an electromagnetic effect, and the armature will overcome the tensile force of the return spring under the action of electromagnetic force attraction and attract to the core, thereby driving the dynamic contact and static contact (normally open contact) of the armature ...

Omron Health Care and Traditional Pharmacy are continuing to build MMC health convenience stores to provide consumers with "one-stop health management and convenient consulting services at their doorstep", which has now been successfully extended to more scenarios such as enterprises, parks and communities. 　　Recently, with the epidemic prevention and control measures...

1. Standard configuration with RS485 interface, Modbus bus communication function; 2. At 3Hz, it can provide more than 150% torque output and start quickly; 3. The carrier frequency of 2-15KHz is adjustable, which can realize silent drive; 4. Equipped with simple energy-saving function; 5. Controlled ...

1. CPM1A-10CDR-A-V1 10-point CPU unit AC100-220V, 6 points in, 4 points relay output (1A is the model code; 10 means that the total number of input and output points is 10 points, specifically 6 points of input and 4 points of output; C means CPU unit; D stands for mixed type, that is, there is a loss ...

1. After determining the object in Omron PLC, click Write Mode in the edit window. 2. Next, directly select the relevant software components and double-click. 3. At this time, you need to change the number through the ladder diagram input and select OK. 4. Such a ...

1/4 of the machine is not running, but the power indicator is on: Reason: The compressor is overheated, so that the compressor turns on the overheating protection and stops automatically. Exclusion method: If the machine runs for a long time without stopping, suddenly stops one day, and can run again after the machine is turned off and cooled, this is ...

Omron sphygmomanometer uses oscillometric measurement method to measure blood pressure, with high accuracy, generally about ±5 Pa, and the measurement method is relatively simple. At the same time, there is a 21-time memory function, which can easily grasp the blood pressure change gauge.

problem 　　At manufacturing sites where social distancing is required, we can increase productivity by reducing the number of workers Due to the pandemic, social distancing was also required on manufacturing sites, and manufacturing with fewer workers had to be achieved quickly. Prior to this, the automatic ...

1. Understand how the shape and scale of the switch affect other characteristics The scale is important when choosing a micro switch. The switching scale is directly related to its characteristics, including current scale, stroke, and operating force. For example, the smallest microswitch on the market today measures 0.50" x 0. ...

1. In the operation of Omron relay, if there is any abnormal sound or other abnormal phenomena, the operation should be stopped immediately, and the professional maintenance personnel should be notified to come for maintenance, and the normal operation can only be put into normal operation after troubleshooting. 2. During the maintenance process, check whether the spring is deformed, old...

Fault detection method 1 1. You can check whether the voltage of the Omron relay is high or low, generally the maximum is between 180V-240V, if the excess value deviation is too large, it is possible that the Omron relay has been damaged. Fault detection method 2 2. ...

(1) Failure of peripheral circuit components This kind of failure is relatively common in PLC maintenance and usually occurs frequently after a certain period of work. If there is a component damage fault in the PLC control loop, the PLC control system will stop working immediately and automatically. The input circuit is a PLC receiving switching quantity ...

Process introduction Since the implementation of the [plastic restriction order] in 2007, plastic packaging has been greatly restricted. Subsequently, all kinds of metal cans represented by beer cans, tea cans, and oil cans are increasing, and metal packaging has begun to usher in a period of rapid development. Metal cans are divided into ...

Process introduction The assembly process of automobile power battery and cell section is divided into: 1.Hot pressing 2.Tab welding 3.Adapter welding 4.Coating 5.Into the shell 6.Top cover welding 　　Among them, top cover welding is the last process, which uses the laser welding process to combine the top cover with ...

Recently, Omron Automation (China) Co., Ltd. (hereinafter referred to as "Omron") and BYD Co., Ltd. (hereinafter referred to as "BYD") successfully held a technical exchange meeting in Shenzhen. Omron industry and technical experts, BYD automobile, light rail, new energy, electronics ...

1. Ambient temperature The specification of the sensor will rule the ambient temperature range of the normal operation of the sensor, such as 40-85 degrees, which varies depending on the product model. It is advocated not to exceed the temperature range specified in the specification book, beyond the normal operating temperature range of the sensor, ...

1. The CPU is abnormal When an abnormal CPU alarm, check all devices connected to the internal bus of the CPU unit. The specific method is to replace the units that may cause failures in turn, find out the faulty units, and deal with them accordingly. 2. The memory is abnormal When the memory is abnormal ...

1. The optical power meter is not accurate, the domestic optical power meter can only test the equipment with small optical power output, and cannot test the EDFA with high power output, and the optical power meter of the optical amplifier must be imported originally, and the inaccurate instrument can not be used as a standard. 2. The flange of the output port is damaged ...

The connection method is as follows: the brown wire is connected to the PLC input point, the PLC com point is connected to the positive pole of the power supply, and the negative pole of the power supply is connected to the blue wire. NPN type: brown is connected to the positive power supply, blue is connected to the negative power supply, the black wire is connected to the PLC input point, and the PLC com point is connected to the positive power supply. NPN is a leak type, and the detected object ...