Soft Touch/Rorobot Finger Module FM-B5V1 Module width: 23mm

Introduction: Rorobot module B-4A30/M is a slender soft claw, suitable for jelly shells, test tubes, badminton, cylindrical, hollow columns and other fragile and fragile objects of non-destructive internal support handling and sorting, to ensure that the product will not be scratched, reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: Rorobot BMC-2076D5[P1/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking ...

Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BMC-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot Soft Jaw BML-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Rorobot Finger Module C3V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: Peculiarity...

Introduction: Rorobot Finger Module C8V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. We...

Introduction: Rorobot Finger Module FM-A8V1, Features and Applicable Scenarios: Combination of Two-Finger Module, Compact Structure, Small Footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Robot Soft Grip BMC-3G20[H]/S, B-3G20[H]/S is a strong small soft gripper that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the higher negative impact of other three-finger soft claws in grabbing ...

Introduction: Rorobot FM-C5V5/LS1 Features: Cooperate with the robotic arm to cope with the flexible production line of small and medium-sized batches and multiple batches in the factory, which can effectively save the production line switching time The maximum opening and closing speed of the soft tentacle claw is 300 times/min, and the highest repeatability is 0.05 ...

Introduction: SoftTouch/Rorobot Gripper BOM Product parameters Skid Mounting Plate: SMP-02 Profile: P-20300 Connector: CP-04 Flange connection module: FCM-R06 Our customer-centric service concept: a full range of services to pursue ...

Introduction:Rorobot Soft Jaw BML-20606, Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Soft Touch/Rorobot Independent Finger Module SMP-01 Features: According to the length of the slot, it is divided into SMP-01 / SMP-02 / SMP-03 It can be used for the assembly between the finger module [FM] and the aluminum profile The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module FM-B5V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot FM-C4V5/LS1 Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 9mm Safe working air pressure: 120kPa Recommended load: 145g Tare weight: 28g Our customer-centric service philosophy ...

Introduction: Soft Touch/Rorobot Finger F-A7 Features: Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece. If you need to customize the shape of the finger or fingertip, please contact customer service. Finger material can be selected conventional ...

Introduction: Soft-Touch/Rorobot Skid Mounting Plate SMP-3S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction:Rorobot BML-2G1211[H] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] and ...