The load switch and combination electrical appliances are mainly composed of frames, isolation switches (the current limiting fuse of the combination is on the isolation switch), vacuum switch tubes, grounding switches, spring operating mechanisms, etc. The product has compact structure, small size, long life, strong closing and breaking ability, and simple operation and maintenance.

1. The high-voltage load switch can be broken with load and has the function of self-extinguishing arc, but its breaking capacity is very small and limited. 2. The high-voltage isolation switch is generally not able to break with load, there is no arc extinguishing cover in the structure, and there is also an isolation switch that can break the load.

1. The high-voltage load switch can be used as a load switch, which has the effect of self-extinguishing arc, but its breaking volume is very small and very limited. 2. The high-voltage isolation switch generally cannot be used as a load switch. There is no arc extinguishing cover in the structure, and there are also disconnectors that can switch loads on and off, but the structure is different from load switches ...

Internal accessories Auxiliary contact: The auxiliary contact is the contact mechanically linked by the main circuit of the circuit breaker, which is mainly used for the display of the circuit breaker opening and closing status, and is connected to the control circuit of the circuit breaker through the opening and closing of the circuit breaker to control or interlock its related electrical appliances. For example, to ...

1. Determine the type and protection form of the circuit breaker according to the requirements of the line for protection - determine the selection of frame type, device type or current limiting type. 2. The rated voltage UN of the circuit breaker should be equal to or greater than the rated voltage of the protected line. 3. The rated voltage of the circuit breaker undervoltage tripper ...

1. What is the reason why the empty trip cannot be pushed? 1. If the air opening itself is faulty or damaged, the air opening should be replaced with a new one. 2. If the line is caused by a short circuit, the line should be found first, and then reconnected.

1. Differences in appearance Although these two types of switches seem to be very familiar, but there are still differences, half of the leakage protection switch is the same as the air switch, and the other half is not, it is equipped with a test jump button and a recovery button, which are not available in the air switch. 2 ...

What are the uses of air switches 1. The air switch is an important electrical appliance in the low-voltage distribution network and power drive system, which integrates control and a variety of protection functions. In addition to completing contact and breaking circuits, it can also generate short circuits to circuits or electrical equipment. Severe...

1. The current value of the air switch is too low, and the load power is greater than the rated power of the air switch. 2. The load joint is not firm, and the joint is not compressed. 3. If there is a short circuit in the line, check whether the electrical plug is dry. 4. The line is aging and leaking, resulting in both the live wire and the neutral line.

1. The air switch is an important electrical appliance in the low-voltage distribution network and power drive system, which integrates control and a variety of protection functions. In addition to completing contact and breaking circuits, it can also generate short circuits to circuits or electrical equipment. Protection against severe overloads and undervoltages, etc.

1. In addition to the short-circuit protection function of the fuse, the air switch can also realize the overload protection of the circuit. 2. The fuse is a one-time protection device, which must be replaced once it is blown and is very troublesome, so its reusability rate cannot be compared with the air switch. ...

2P means two poles, which means that this air switch has two connection ports, one to connect to the neutral wire and one to the live wire, which is suitable for single-phase circuit connection, or can also be used to connect two-phase power supply in a three-phase circuit. 3P is the meaning of three poles, there are three connection ports, and all of them are ...

1. Common air switch models in the family Common family models: DZ series, C16, C32. C40, C80, C100, C120 and other products, of which C represents the starting current, such as: C32 means that the starting current is 32A, which can drive a 6500 watt water heater, C40 ...

Ambient air temperature: upper ambient air temperature +40°C; The lower limit of ambient air temperature is -5°C; The average temperature of the ambient air for 24 hours does not exceed +35 ° C. Altitude: The altitude of the installation site does not exceed 2000m. Atmospheric conditions: Atmospheric relative humidity at ambient air temperature of +4 ...

The socket, lamp head, kitchen, bathroom, refrigerator, air conditioner of each route should be put out separately, and each route should have a separate air switch, high-power rooms, such as kitchens and bathrooms, the line of more than 4 square millimeters should reach 20A, and the general lamp head line should only be 16A, and each line ...

The meaning is different, the scope of application is different, and the role is different. Air opening C represents the current, and the D model represents the power. The scope of use is different. If it is a household electricity, the air switch of the C model is generally chosen. The role is different. Type C it is used for home lighting use, Type D is suitable for ...

First, the principle is different 1. Class Cb automatic switch is an electronic product that converts one or more load circuits from one power source to another 2. PC-level automatic transfer switchgear is an electrical appliance that converts one or several load circuits from one power supply to another. ...

First, first place the dual power supply on the adjustment table, and the phase wire and the neutral wire (neutral line) are docked in place, and can not be connected wrongly. Second, after the line is connected, it is necessary to check the installed line, and then turn on the main switch of the debugging station to turn on the common and standby working power supply. Three, when the double ...

1) Ambient air temperature: The upper limit of ambient air temperature is +40°C, the lower limit of ambient air temperature is -5°C, and the average value of ambient air temperature for 24h does not exceed +35°C 2) Altitude: The altitude of the installation site does not exceed 2000m. 3) Atmospheric conditions: Atmospheric relative humidity in the surrounding air ...

1) When there is a power outage for any reason and the power cannot be restored in a short period of time, the backup power supply must be activated 1. Cut off the circuit breakers of the mains power supply (including the circuit breakers of the control cabinet in the distribution room, and the mains power supply cut-off of the dual power switching box), and pull the double-cast anti-reverse switch to the side of the self-provided power supply to ensure that the power supply is protected.

It is mainly divided into ATS and STS. STS static toggle switch STS (Static Transfer Switch), also known as static transfer switch. The STS automatically switches to the second channel to supply power to the load after the first channel fails.