Introduction: Rorobot Passive Driver PCU2-V, Energetic Passive Driver
Features:
-80-300kPa digitally adjusts the output air pressure range, suitable for a full range of soft jaws and soft finger drives.
To precisely adjust the positive and negative pressure, you can choose manual knob voltage regulation (PCU2-M) or electronic analog voltage regulation (PCU2-V).
The integrated panel integrates the digital display and the operation buttons at a glance.
It also has manual (button), I/0 and MODBUS control modes, and is equipped with various robotic arms and PLC terminals.
It has an attitude feedback signal function. It has an intelligent output alarm signal, and the large-screen data alarm is clearly visible, which is safe and does not need to worry about misoperation.
Product parameters
Rated voltage: 24VDC
Quota power: 24W
Lifespan: 50 million times
Input Air Supply:
0.45-1.00MPa
Dry, clean and stable
Flow rate> 200L/min
Output air pressure: -80-300kPa
Positive pressure flow: 260L/min
Vacuum flow: 80L/min
Housing material: aluminum alloy anodizing
Net weight: 4.40kg
Degree of protection: IP54
Working mode: continuous signal drive
Operating noise: 50db
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only every process, every action, and every detail of the service can be professional and careful, in order to meet or even exceed customer expectations, so that customers are satisfied and recognize us. Honest, professional, affordable, fast, so let you rest assured." Integrity and professional service, affordable price, and continuous improvement" is our service concept.
This article introduces the PCU2-V products of Rorobot Passive Driver, if you are interested in Rorobot Passive Driver, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
Rorobot B-20005V **Large load 30g
Introduction: Rorobot B-20005V
Features:
Replaceable flexible chucks
The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G
It can be used as a clamp or external support
Recommended for use with soft-touch actuators
Products...
|
|
Soft Touch/Rorobot Finger Module FE-A3V1 Module width 29mm
Introduction: Soft Touch/Rorobot Finger Module FE-A3V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, and it is suitable for clamping small, light and thin workpieces.
Features:
Features and applicable scenarios: ...
|
|
Soft Touch/Rorobot Finger Module FM-B8V1 Finger height 21mm
Introduction: Rorobot Finger Module FM-B8V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces.
Features:
Features and applicable scenarios: two-finger ...
|
|
Soft Touch/Rorobot Finger Module FM-A7V1 Finger length 97mm
Introduction: Rorobot Finger Module FM-A7V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, suitable for clamping tiny, thin and light workpieces, and the fixing method: can be fixed from three directions.
Features ...
|
|
Soft Touch/Rorobot Soft Touch Module Slip Mounting Plate SMP-14 has a dead weight of 16.2g
Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-14
Features:
According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16
It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile
The installation angle of the soft beak module and the ...
|
|
Soft Touch/Rorobot Finger Module B4V3 Finger width 18mm
Introduction: Rorobot Finger Module B4V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted.
Features:
Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...
|
|
Soft-Touch/Rorobot Skid Shift Mounting Plate SMP-2S slot width 4.2mm
Introduction: Soft-Touch/Rorobot Slip Mounting Plate SMP-2S
Features:
It is divided into different styles according to the shape and length of the groove
It can be used for assembly between the finger module [FM] and the flange connection module [FCM].
The mounting angle and position of the finger module [FM] can be adjusted freely
...
|
|
Rorobot BMC-20005V[P] External gripping blessing force 0-0.3N
Introduction:Rorobot Robot Soft Gripper BMC-20005V, B-20005V/S can be used well for 0.18mm-3mm between small and light and thin special-shaped workpieces, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...
|
|
Rorobot B-3B18 weight 6.4g
Introduction: Rorobot Soft Beak B-3B18
Features:
Replaceable flexible chucks
The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G
It can be used as a clamp or external support
Recommended for use with soft-touch actuators
Product References ...
|
|
Soft Touch/Rorobot Finger Module FM-C4V2 Module Length 51mm
Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional)
...
|
|
FlexTouch/Rorobot Flange Connection Module FCM-R08
Introduction: Rorobot Flange Connection Module FCM-R08
Features:
Conform to ISO9409-1:2004 (i.e. GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market.
It is recommended to carry a large load of 20kg
Suitable for non-standard gripper combinations ...
|
|
Soft Touch/Rorobot Soft Jaw BMC-2G1624[HB]/S Opening and closing frequency 6 times/second
Introduction: Rorobot Soft Jaw BMC-2G1624[HB]/S
Features:
Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum
In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased
Soft claws ...
|
|
Soft Touch/Rorobot Soft Jaw BML-4BG64[P]/S Opening and closing frequency 6 times/second
Introduction:Rorobot BML-4BG64/S, B-4BG64/S is an external gripper type soft jaw, the recommended clamping workpiece size is (28-50) mm, the opening and closing size is (50.4-80) mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S is ...
|
|
Rorobot BML-4H18[H]/S opening and closing frequency: 6 times/second
Introduction: Rorobot BML-4H18[H]/S
Features:
The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D.
The soft claw material is divided into conventional type [H and non-marking ...
|
|
Soft Touch/Rorobot Finger F-A4 Height 28mm
Introduction: Soft Touch/Rorobot Finger F-A4
Features:
Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece.
If you need to customize the shape of the finger or fingertip, please contact customer service.
Finger material can be selected conventional ...
|
|
Soft Touch/Rorobot Quick Change Module QCM-01R Vertical tension 150N
Introduction: Soft Touch/Rorobot Quick Change Module QCM-01R, Quick Change Module is used for automatic quick replacement of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, installed...
|
|
Soft Touch/Rorobot Finger Module B8V5 Module height 51mm
Introduction: Rorobot Finger Module B8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.
|
|
Soft Touch/Rorobot Finger Module B7V5 Finger length 73mm
Introduction: Rorobot finger module B7V5, features and applicable scenarios: the module is thinner, the finger spacing of the installation module is only 10mm, suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.
|
|
Soft Touch/Rorobot Finger Module B8V3 Finger width 18mm
Introduction: Rorobot Finger Module B8V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted.
Features:
Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...
|
|
Rorobot BMC-3G20[HAS]/S
Introduction: Rorobot BMC-3G20[HAS]/S
Features:
The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G.
Soft-touch materials are divided into regular [H] and non-...
|
|