The function of the tension spring bracket in the bus system is to fix the orientation and stability of the bus duct, and it must be very careful during construction, otherwise the bus duct will fall, which will cause a very serious accident.
The device steps of the tension spring support in the bus system:
The first step is to check the spacing between the bus duct and the wall according to the relevant design scheme of the bus system, and advocate that the spacing should exceed 100m (at least 50mm);
The second step is that the size of the angle steel base of the bus system should match the size of the tension spring support;
The third step, before the tension spring support device, ensure that the channel steel on the ground is in the same vertical line;
The fourth step is to hang the bus duct in the bus system to ensure that the bottom of the bus duct connector and the ground are separated by 800mm (at least 550mm);
The fifth step, according to the design drawings of the bus system, the stud bolt is fixed on the channel steel, and then the tension spring and the tension spring bracket (keep the natural condition) are installed, and the nut is rotated to the appropriate position;
Sixth, according to the orientation of the tension spring support, open a hole in the bus duct in the system (according to the pre-marked scale on the diagram);
Step 7: Use M6 screws to fix the tension spring bracket on the bus duct;
The eighth step is to tighten the nut and press the tension spring upwards to balance the supporting force of the tension spring and the weight of the bus duct.
|
More on that
|
Fast protection of medium and low voltage busbars – Wienal
1.It is necessary to install arc light maintenance
Arc maintenance in foreign countries has nearly 20 years of history, the first set of maintenance devices in 1995 has been put into operation, China's previous imported units in the introduction of foreign complete sets of arc light maintenance (such as Guohua Tianjin Panshan Power Plant), domestic units ...
|
|
What are the hazards of 220V DC in the bus system - Wiener
The grounding of the DC system should include two situations: the one-point grounding of the DC system and the two-point grounding of the DC system.
In the DC system, the positive and negative poles of DC are insulated from the ground, and there is no grounding current when generating a ground current when one pole is grounded.
|
|
Wiener fixed and busbar mounting
Precautions for the device
VDE 0660 Specification Section 107 / EN 60947-3 Specification / IEC 60947-3 Specification
3 poles are broken at the same time, double breakpoints.
Operator-independent, safe opening/closing, in position ...
|
|
The role of the busbar in the excitation system – Wiener
The bus PT is used to measure the bus voltage on the high-voltage side of the main transformer, and is used to assist in grid connection. Before starting the synchronous grid connection, the excitation system actively adjusts the terminal voltage according to the bus voltage measured by the bus PT, so that the voltage on both sides of the grid-connected switch is basically equal, which is convenient for the same period of grid connection.
...
|
|
The busway phase in the low-voltage incoming line - Wiener
According to the requirements of the relevant specifications, the placement method of the three-phase busbar can be roughly divided into two kinds according to the model of the low-voltage distribution cabinet and the different manufacturers: the horizontal placement and the placement of the down wire.
|
|
A detailed description of the Wiener comb busbar and connection terminals
The Wiener comb busbars and connection terminals are available with QUADRON®CrossLinkBreaker in size 000/00
Recommended installation: Wire entry at the lower end of the NH-fuse disconnector through the comb busbar.
In the mounting position ...
|
|
Features of busway power supply system - Wiener
1. Trunk power distribution system, simple wiring and reliable operation.
2. It is convenient to tap, and you can tap without cutting off the main power supply. Large power supply capacity up to 6300A current-carrying capacity.
3. High dielectric strength, strong overload, superior fire performance. Good heat dissipation performance, low impedance ...
|
|
What is tubular busbar and dense busbar - Wiener
What is a tubular busbar
Tubular bus bar is a kind of bus bar product with copper tube or aluminum alloy tube as conductor and external insulation. The tubular bus has the characteristics of high current (12000A), high mechanical strength, good insulation, wide application range, etc., ...
|
|
The way in which the Wiener high-voltage busway is selected
In the selection, the following elements should be fully considered: fire protection specifications, insulation layer to flame retardant, good temperature resistance, high temperature is not easy to release harmful gases, structure type to avoid chimney effect, should give priority to the use of aggregate insulation layer bus duct, such as the use of air insulation type, it must be in the electric ...
|
|
Introduction to several power supply systems – Wienal
At present, China has five power supply systems: IT, TT, TN-c, TN-c-s and TN-S. They have their own advantages and disadvantages, and we should choose sensitively according to the actual situation in life.
Five power supply systems
1.IT power supply system
In a ...
|
|
Classification of the use of busway in different places - Vernal
(1) General bus duct
Non-flame retardant and non-fire-resistant bus duct selected for general load power distribution. In the event of a short circuit, it will be incinerated until it is connected to other busbars, which can easily cause fire accidents.
(2) Flame retardant bus duct
...
|
|
Busbar system reverse operation – Wiener
(1) For the charging of the spare bus, when there is a bus tie circuit breaker, the bus tie circuit breaker should be used to charge the spare bus. At this time, the maintenance device of the bus tie circuit breaker should be fully invested, and the relevant maintenance value and time limit should be changed to a small size, so that when there is a problem with the bus, the bus tie circuit breaker can be quickly tripped, cut off...
|
|
Introduction to busbars in Wiener's electrical system
The bus bar is an intermediate link in the voltage distribution device at all levels, and its role is to gather, distribute and transmit electric energy. It is mainly used for the connection of the electrical main circuit between the power plant generator outlet line and the main transformer, the plant transformer and the distribution box, also known as the busbar.
...
|
|
Introduction of busbar, busway and busway bridge - Vernal
generatrix
In the field of electricity, the busbar can also be called the busbar, busbar, etc., most of which refer to the busbar or power supply trunk in the high and low voltage cabinet, which is used to connect multiple electrical lines. The system will install various interface cards through the bus, and transmit various data to the devices connected to the interface cards.
|
|
220V DC Hazard of Bus System – Wiener
The grounding of the DC system should include two situations: the one-point grounding of the DC system and the two-point grounding of the DC system.
In the DC system, the positive and negative poles of the DC are insulated from the ground, and when the ground of one pole is generated, there is no grounding current due to the fact that there is no grounding current.
|
|
NH-Fuse Type Disconnector Instructions for Use
When switching on and off components, you should pay attention to the following:
–In accordance with VDE-0105-100, only operation by electrical professionals or persons with electrical knowledge is allowed (operation without electricity, closing, disconnecting, and replacing fuses ...).
|
|
Wiener busbar system PT disconnection treatment
The judgment of PT three-phase voltage loss (symmetrical disconnection) is fundamentally the same for each manufacturer, and it is judged according to the three-phase no voltage and the current of the line. The same is true for PT asymmetrical wire breakage. After analyzing the characteristics of PT wire breaking, the specific judgment of PT asymmetric wire breaking of different manufacturers ...
|
|
Technical requirements for busway system – Wiener busbar
1. The conductor of the bus bar is a high conductivity TMY electrical hard copper bar rolled by T2 electrolytic copper, and the purity of copper must be ≥ 99.95%, and copper-aluminum alloy or other mixed alloy non-pure copper conductor materials shall not be used, and the copper plate is tin plated on the full length.
2. The raw material of the neutral wire and the phase wire in the bus system is the same.
|
|
The importance of busbar systems in low-voltage switchgear
One of the characteristics of low-voltage switchgear is the multi-functional busbar system.
The bus bar is a conductor that connects large electrical equipment such as generators and transformers with various electrical equipment. The role of the bus is to, sub-...
|
|
Wiener enclosed busbar installation
Closed busway is a busbar system composed of metal plates (steel plates or aluminum plates) as protective shells, conductive strips, insulating materials and related accessories. It can be made into a piercing closing bus with spaced piercing junction boxes, or a feed-in closing bus without a junction box in the middle. ...
|
|
Contact
working hours
