Soft Touch/Rorobot Independent Finger Module SMP-02 slot width 4.2mm

Introduction: Soft Touch/Rorobot Finger Module FMA5-V3 Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner and lighter, and the finger spacing of the installation module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger F-C8 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a grip force** of up to 300% of a conventional grade finger. Defend...

Introduction: SoftTouch/Rorobot Connection Module CM-S04 Features: A full range of soft beak modules can be installed at the end Can be mounted on the Flexible Series Slip Mounting Plate [SMP] page.50 Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products...

Introduction: Rorobot Air Driver iPCU 2, with two options: standard iPCU 2-SMN and high-speed iPCU 2-HMN, the high-speed type has a larger flow rate and faster response speed, and is suitable for high-speed handling conditions. Features: With 3 adjustable ...

Introduction: Rorobot Finger Module C7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Finger Module FMA6-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction:Rorobot BML-2G1211[H] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] and ...

Introduction: Soft Touch/Rorobot Finger F-B8 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a grip force** of up to 300% of a conventional grade finger. Defend...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-14 　　Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-15 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Soft Touch/Rorobot Finger Module C7V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Use Screw Accessory Kit PK) and Simplify the Trachea Arrangement. It is mostly used in scenarios where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm Features: ...

Introduction: Rorobot Soft Gripper BMC-4G64[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Soft Jaw BML-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When grabbing the workpiece, it can minimize the damage caused by the soft finger itself to the workpiece. We...

Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot B-3C24[H]/S Features: The fingertips are opened in the positive pressure state, clamped in the vacuum state, and it is recommended to use it with a soft-touch air driver, and it supports the fingertip distance G and the external support finger distance D edible working air pressure adjustment. Soft-touch materials are divided into ...

Introduction: Rorobot BMC-3A18[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G and the external support fingertip distance D. The soft claw material is divided into ...

Introduction: Soft Touch/Rorobot Finger F-C5 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a grip force** of up to 300% of a conventional grade finger. Defend...