The new base plate has been developed and upgraded according to the technical parameters of the Dark Horse system, and is specially adapted to the HIMax safety system. In addition to their comprehensive functionality, these baseplates also offer the look and feel of the Dark Horse System baseplates for use in non-risk areas. The new product range masks all signal types and provides customers with a common solution that meets the requirements of a wide range of plants.
The new base plate offers greater flexibility:
In addition, the analog baseplate is equipped with a HART connector, which can be easily accessed even if the baseplate is already installed and wired. The innovative transformation of the main controller can also be completed. This is because the corresponding analogue modules support HART communication and the HART signals can be smoothly processed by the safety system.
The new baseplate series masks all signal types. Commonly used signals from the safe zone – analog inputs and digital inputs and outputs – are available in single and dual channel backplanes. A single-channel backplane with an analogue output signal completes the entire product range.
The signal distribution base ensures that the input signals are transmitted to the control side of the HIMA system. Tension spring terminals can be used for wiring as an option. Once the customer has selected the safety-related control system from HIMA, they can use another conventional control system that does not require a specific manufacturer.
The pre-configured system cables and base plates of the H series ensure that the system wiring between the field device and the automation control terminal meets safety standards. This simplifies commissioning and reduces the amount of manual wiring. The isolated barrier can be installed on the base plate without any tools and can even be replaced while the system is running. The coded latch prevents the module from being misplaced and ensures that safety-relevant parameters are followed. The power module is redundant and fixed by the backplane.
The barrier base plate can be mounted on a 35 mm DIN rail, which can be mounted horizontally or directly in the control cabinet. Signals from risk areas are transmitted directly to the barrier baseplate, which has no terminals of its own. When replacing a module, no additional wiring and circuit checking are required. This saves time and money for planning, wiring and documentation, and maximizes equipment utilization.
The base plates for the system manufacturer are tested in the original control system and can be supplied with the relevant test reports.
Masking All Signal Types:
The uniform planning simplifies the configuration and ensures a concise and professional wiring layout in the control cabinet
The signal distribution function enables the use of general, vendor-independent interfaces
System solutions for safe analogue output are possible – supporting HIMA's key operating principles
The new plan follows the characteristics of the past:
The new planning of the series is based on the HIMA product standard for non-risk areas, which guarantees the same appearance as the previous products. The status LEDs that HIMA users are aware of facilitate the handling of the baseplate and reduce the number of troubleshooting moments.
Bright spot:
Configured modules can be replaced in the system operation
The new planning of the series is based on the HIMA product standard for non-risk areas, which guarantees the same appearance as the previous products. The status LEDs that HIMA users are aware of facilitate the handling of the baseplate and reduce the number of troubleshooting moments.
The installation and replacement of the modules does not require any tools or wiring
|
More on that
|
Precautions for P+F safety barriers
First, it is necessary to pay attention to the capacitive and inductive resistance of cables and field equipment, explosion-proof is the explosion-proof system, in addition to the need for P+F safety barriers to reach the required explosion-proof level, the energy storage of cables and field equipment is also a key issue. Especially after parametric certification replaces system certification, engineering companies are especially ...
|
|
A brief introduction to our sensors
Proximity sensors are a general term for sensors that replace contact detection methods such as limit switches and do not require contact detection of the detected object. It is capable of converting information about the motion and presence of objects into electrical signals. The detection method of replacing the electrical signal includes: using an electromagnetic induction bow to ...
|
|
Q&A on ultrasonic sensor technology
Q1: How does the ultrasonic sensor work?
Ultrasonic sensors are used to measure the detection function of emitting high-frequency sound pulses that are inaudible to the human ear, which are dispersed in the air into a conical shape and reflected back as soon as they hit an object. Ultrasonic ...
|
|
Troubleshooting for coding problems
P+F encoders are devices that compile signals (e.g. bit streams) or data and convert them into signals that can be communicated, transmitted, and stored. The P+F encoder converts angular or linear displacements, the former known as the code disc and the latter into an electrical signal. Therefore, the phenomenon: 1, ...
|
|
We made a wonderful appearance at SIAF 2022
The 2022 Guangzhou World Industrial Automation Skills and Equipment Exhibition (SIAF) landed at the China Import and Export Fair Complex on March 3, kicking off the prelude to this year's industrial automation career exhibition. As the driver and innovator of Industry 4.0, we continue to provide customers with the future of the future.
|
|
Doujiafu helps intelligent robots to fight against the war
Now that the prevention and control of the new pneumonia epidemic has entered a critical period, how can it be useful to reduce cross-infection in hospitals and prevent the spread of the epidemic? Reduce the operational pressure of front-line medical personnel and help prevent and control the epidemic? All of them have become the key policies that have attracted wide attention. From long-distance medical care to intelligent robots ...
|
|
Common dry contact signals for safety barriers
The dry contact of the barrier is an electrical switch that has two positions: closed and disconnected. There is no polarity between the two contacts of the dry contact and is interchangeable. That is, a simple switch, the contact does not provide power supply, and the power supply can be used to control the condition of the equipment. But it doesn't offer ...
|
|
The main classification of encoders – Beggarb
Encoders can be classified as follows.
1. Classification according to the engraving method of the code disc
(1) Incremental type: that is, every time the viewpoint of the unit is rotated, a pulse signal is announced (there is also a sine and cosine signal, and then it is ...
|
|
Pre-selection of sensors
In the early application and selection of sensors, how to choose is a very important point, and the selection is smooth, and the following will briefly talk about how the sensor is selected in the early stage.
The use of the sensor in practical operation is relatively common and may be practical ...
|
|
Points to note for encoder installation
1. Each electrical interface has its own characteristics, but also has different baud rate and transmission interval, which can be selected according to the specific application environment of the site, and the actual transmission interval is very related to the transmission rate, encoder and communication cable installation disturbance environment, grounding, cable material selection, etc.
...
|
|
A common problem with the failure of pressure sensors – our sensors
First, the problem of the pressure sensor sealing ring
If the output of the pressurized transmitter does not change, and the output of the pressurized transmitter changes suddenly, and the zero position of the pressure relief transmitter cannot be returned, it is likely that the problem of the pressure sensor sealing ring. It is common because of the standard reason of the sealing ring, the sensor is tightened ...
|
|
Sensors used in obstacle avoidance for industrial robots - Bejiafu
Mobile robots need to obtain information about surrounding obstacles in real time through sensors, including scale, shape, and orientation information, to complete obstacle avoidance. There are many kinds of sensors used in obstacle avoidance, and the common ones are vision sensors, laser sensors, infrared sensors, ultrasonic sensors, etc.
...
|
|
The R100 and R101 series of photoelectric sensors – we are blessed
With the launch of the new R100 and R101 series of photoelectric sensors, we have expanded our Sensing Skills 4.0 product line with innovative intelligence.
The R100 and R101 range include two light source plans: the robust PowerBea...
|
|
How to choose a sensor in the early stage?
In the early application and selection of sensors, how to choose is a very important point, and the selection is smooth, and the following will briefly say how the sensor is selected in the early stage.
The Viewpoint Sensor is in the real ...
|
|
Engineered Vibration Sensor Test Methods – Blessing
In the field of engineering oscillation testing, there are various test methods and methods, but they can be divided into three categories according to the measurement methods of various parameters and the physical properties of the measurement process.
1. Mechanical quizzes
Will the works oscillate ...
|
|
Introducing the sensor
From leveling cranes and monitoring the inclination of front-end loaders to operating elevators, inclination and acceleration sensors can be used in a variety of ways. These sensors are guaranteed to measure even in harsh conditions. Thanks to the innovative split unit concept, the F99 series ...
|
|
Anti-corrosion method of pressure sensors
Pressure sensors are used in all walks of life, especially in the industry, many pressure sensors, but the industry generally requires pressure sensors to be able to prevent corrosion, pressure sensor joints and cavities are imported stainless steel for all processing, as the pressure transmitter projectile body of stainless steel material resistance...
|
|
Installation and assembly of ultrasonic sensors
Ultrasonic sensors are used for the inspection of printed circuit boards (PCBs), where ultrasonic sensors are used to inspect printed circuit boards. So what factors need to be taken into account when installing and assembling ultrasonic sensors?
Ultrasonic ...
|
|
Photoelectric sensor sensing mode – Doublebless
The pass-through beam device consists of an acceptor located within the line of sight of the transmitter. In this mode, an object is detected when the beam is blocked from the transmitter to the receiver.
The retroreflective device places the transmitter and receiver in the same direction, and uses the reflector to ...
|
|
Anti-jamming technology for sensors – we are blessed
1. Shielding skills
Containers are made from metal materials. Wrapping circuits that require maintenance between them can effectively prevent the disturbance of electric or magnetic fields, which is called shielding. Shielding can be divided into electrostatic shielding, electromagnetic shielding and low-frequency magnetic shielding.
2. Electrostatic shielding
...
|
|
Contact
working hours
