Soft Touch/Rorobot Finger F-A8 Height 28mm

Introduction: Rorobot Soft Beak Module BM-2B Features: Can be mounted on connection module [(M] or flange connection module [F(M] The soft beak module consists of a soft beak and matching fittings The module combination is supplied with a straight-through fitting fitting (PN-066) or ...

Introduction: iPCU2 has two options: standard iPCU2-SMN and high-speed iPCU2-HMN, the high-speed type has a larger vacuum flow rate and is suitable for high-speed handling conditions. iPCU2 Passive Driver: Compact soft-touch passive actuator. -90~300kPa three-speed adjustable output air pressure range ...

Introduction: Rorobot BML-4G64[HAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Finger Module C7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Finger Module B4V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction:Rorobot Soft Jaw BMC-1G364030[H]/M, is a strengthened version of the single finger soft jaw, the recommended distance between the fingertip and the workpiece is (19-28) mm, the recommended load of the single finger soft jaw is (0-500)G, and the external gripping force is (0-11)N. Features: Positive pressure state fingertip hit ...

Introduction: Rorobot BMC-2015D5/S Features: It can be installed in the Straight Inlet Connection Module [CM] series or the Test-Through Inlet Flange Connection Touch Group [FCM] series Straight-through or side-intake options are available The fingertips are open in the positive pressure state, and the negative pressure ...

Introduction: Rorobot Soft Jaw BMC-3B24[H]/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch material points ...

Introduction: Soft Touch/Rorobot Finger F-A5 Features: Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece. If you need to customize the shape of the finger or fingertip, please contact customer service. Finger material can be selected conventional ...

Introduction: Rorobot Finger Module C8V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the installation module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Flange Connection Module FCM-R08 Features: Conform to ISO9409-1:2004 (i.e. standard GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market. It is recommended to carry a large load of 20kg Suitable for non-standard gripper combinations ...

Introduction: Soft Touch/Rorobot Stand-Alone Finger Module SMP-02 Features: According to the length of the slot, it is divided into SMP-01 / SMP-02 / SMP-03 It can be used for the assembly between the finger module [FM] and the aluminum profile The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module FM-A5V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, suitable for clamping tiny, thin and light workpieces, and the fixing method: can be fixed from three directions. Features: ...

Introduction: Soft Touch/Rorobot Finger Module A8V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Soft Beak B-20006 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Products...

Introduction: Rorobot Soft Jaw BMC-1G364030[HAS]/M, is a strengthened version of the single finger soft jaw, the recommended fingertip and workpiece distance is (19-28) mm, the recommended load of one finger soft jaw is (0-500) G, and the external gripping clamping force is (0-11) N. Features: Positive pressure state fingertips ...

Introduction: Rorobot BML-3G20[HAS]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional [ ...

Introduction: Rorobot BMC-2076D5[P1/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking ...

Introduction: iPCU 2 is available as a standard iPCU 2-SMN and a high-speed iPCU 2-HMN compact controller. Small size, light weight, easy installation. The high-speed type has a larger flow rate and faster response speed, and is suitable for high-speed handling conditions. ...

Introduction: Rorobot Flange Connection Module FCM-S01, Flange Connection Module [FCM] is a connection between the end of the robotic arm and the sliding mounting plate [SMP], which can be used with the quick-change module [QCM], which is divided into spring rod type (S) and fixed rod type (R). Features: Compliant with IS...