Introduction: Rorobot Finger Module A3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping small, thin and light workpieces. It can also be used in series (using the screw kit PK), but each finger needs to be supplied independently compared to the V4.
Features:
Features and applicable scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping small, light and thin workpieces. It can also be used in series (using the screw kit PK), but each finger needs to be supplied independently compared to the V4.
Fixing method: It is fixed with a chute nut, and when it is installed with the sliding mounting plate (page.50), it can be adjusted to three degrees of freedom of front and back, left and right and rotation.
Air intake method: The air intake connector can only be installed in one direction (outside of the finger)
Product parameters
Fingertip stroke: 16.5mm
Negative pressure stroke: 8mm
Positive pressure stroke: 8.5mm
Module height: 58mm
Finger height: 28mm
Module length: 88mm
Finger length 41mm
Module width: 31mm
Finger width: 24mm
Tare weight: 76g
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only every process, every action, and every detail of the service can be professional and careful, in order to meet or even exceed customer expectations, so that customers are satisfied and recognize us. Honest, professional, affordable, fast, so let you rest assured." Integrity and professional service, affordable price, and continuous improvement" is our service concept.
This article introduces the A3V5 product of Rorobot Finger Module, if you are interested in Rorobot Finger Module, please also contact our customer service, we look forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
Soft Touch/Rorobot Finger Module FM-A4V2 Finger width 24mm
Introduction: Rorobot Finger Module FM-A4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) .
...
|
|
Soft Touch/Rorobot Soft Jaw BML-4G64[H]/S Opening and closing frequency: 6 times/second
Introduction: Rorobot BML-4G64[H]/S
Features:
The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G.
Soft-touch materials are divided into conventional type [H] and non-marking ...
|
|
Rorobot FM-A5V5/LS1[P]
Introduction: Rorobot FM-A5V5/LS1
Features:
Product parameters
Positive pressure stroke: 24.5mm
Negative pressure stroke: 19mm
Safe working air pressure: 120kPa
Recommended load: 280g
Tare weight: 90g
We take the guest ...
|
|
Soft Touch/Rorobot Finger Module B4V4 Module length 72mm
Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm.
Features:
...
|
|
SoftTouch/Rorobot Finger Module FM-B3V2 Module width 25mm
Introduction: Rorobot Finger Module FM-B3V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional)
...
|
|
SoftTouch/Rorobot Finger Module A8V5 Module length 158mm
Introduction: Rorobot Finger Module A8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.
|
|
Soft-touch/Rorobot Slip Mounting Plate SMP-4S weighs 52.3g
Introduction: Soft-Touch/Rorobot Slip Mounting Plate SMP-4S
Features:
It is divided into different styles according to the shape and length of the groove
It can be used for assembly between the finger module [FM] and the flange connection module [FCM].
The mounting angle and position of the finger module [FM] can be adjusted freely
...
|
|
FlexTouch/Rorobot Flange Connection Module FCM-R04
Introduction: FlexTouch/Rorobot Flange Connection Module FCM-R04
Features:
It complies with the ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market.
Light weight, suitable for lightweight articulated robots, ...
|
|
Rorobot FM-A6V3/LS1[PAS]
Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. We...
|
|
Soft Touch/Rorobot Soft Jaws BMC-4BG64[PAS]/S The recommended load is 1500g
Introduction:Rorobot soft claw BMC-4BG64/S, B-4BG64/S is an external gripper type soft claw, the recommended clamping workpiece size is (28-50) mm, the opening and closing size is (50.4-80) mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S is ...
|
|
Rorobot BMC-20006[PAS]
Introduction: Rorobot BMC-20006
Features:
The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G
The soft claw material is divided into conventional type and non-marking type.
|
|
Rorobot B-4B50[P]/S The recommended load is 500g
Introduction: Rorobot B-4B50/S
Features:
The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D.
Soft-touch materials are divided into conventional ...
|
|
Rorobot BMC-2076D5 [P1/S Safe working air pressure 80kPa
Introduction: Rorobot BMC-2076D5[P1/S
Features:
The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G.
The soft claw material is divided into conventional type and non-marking ...
|
|
Rorobot BML-1G364030[H]/M Opening and closing frequency: 6 times/second
Introduction: Rorobot Robot Soft Jaw BML-1G364030[H]/M, is a strengthened version of the single finger soft jaw, the recommended fingertip and the workpiece distance is (19-28) mm, the recommended load of the single finger soft jaw is (0-500) G, and the external gripping force is (0-11) N.
Features:
Positive pressure ...
|
|
Soft Touch/Rorobot Quick Change Module QCM-01R Vertical tension 150N
Introduction: Soft Touch/Rorobot Quick Change Module QCM-01R, Quick Change Module is used for automatic quick replacement of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, installed...
|
|
Rorobot BML-2G1211[H] Recommended load is 120g
Introduction:Rorobot BML-2G1211[H]
Features:
The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G
The soft claw material is divided into conventional type [H] and ...
|
|
Soft-touch/Rorobot Connection Module CM-S04 weighs 28g
Introduction: SoftTouch/Rorobot Connection Module CM-S04
Features:
A full range of soft beak modules can be installed at the end
Can be mounted on the Flexible Series Slip Mounting Plate [SMP] page.50
Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products...
|
|
Rorobot BML-3B14[P]/S
Introduction: Rorobot Soft Jaw BML-3B14/S
Features:
The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips.
The soft claw material is divided into conventional type and non-marking type, when ...
|
|
Soft Touch/Rorobot Finger Module FM-C4V2 Module Length 51mm
Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional)
...
|
|
FlexTouch/Rorobot Flange Connection Module FCM-S01
Introduction: Rorobot Flange Connection Module FCM-S01, Flange Connection Module [FCM] is a connection between the end of the robotic arm and the sliding mounting plate [SMP], which can be used with the quick-change module [QCM], which is divided into spring rod type (S) and fixed rod type (R).
Features:
Compliant with IS...
|
|