Wuzhong instrument - what is the anti-loosening effect of spring washers?

The filter is an indispensable product in the fluid pipeline, which is generally installed at the inlet end of the pressure relief valve, pressure reducing valve and water level valve set equipment, which has the effect of eliminating impurities in the medium and avoiding the phenomenon of other equipment being stuck. After the medium passes through the filter cartridge equipped with a certain standard screen, the impurities are blocked.

The process of shell experiments and seal experiments done by turbine fixed ball valves in some artificial environments is as follows. Double blocking and discharge function of turbine fixed ball valve: the turbine ball valve is fixed by using tension spring preload float valve seat, when the valve is in two different states, full open and fully closed, the fluid is ...

The control valve, also known as the control valve, is a device in the field of industrial automation process control that uses power operation to change the process parameters such as the flow, pressure, temperature, and liquid level of the pipeline medium.

1. According to the requirements of different flow characteristics, the electric sleeve control valve can be easily replaced with a linear flow characteristic sleeve or an equal percentage of flow characteristic sleeve, and can replace the sleeve with different flow capacity according to the different requirements of flow size. 2. Electric sleeve simple control valve in high temperature ...

1. Units and scales (scales) The scale (scale) unit of the temperature instrument is uniformly selected as Celsius (°C). 2. Detect (measure) the insertion length of the component The selection of the insertion length should be based on the detection (measurement) of the component insertion.

The actuator of the control valve has pneumatic type, electric type and electro-hydraulic linkage type, and the pneumatic equipment is divided into barrier type and cylinder type. Depending on the action when the operating signal and the drive source disappear, the actuator has a forward type, a reverse type, a non-directional type, and a persistent type. The positive type is used in the operation signal and drive ...

(1) The conditioning valve does not operate. The symptoms and causes are as follows: 1. No signal, no air source. (1) The air source is not opened, (2) because the water contained in the air source freezes in winter, resulting in the blockage of the air duct or the blockage of the filter and pressure reducing valve, (3) the compressor is faulty; (4) Leakage of air source main pipe. 2． ...

Double-seat cast ball angle valve The nominal diameter is 40-200 mm Nominal pressure ANSI 125, 150, 300, 600JIS10, 16, 20, 30, 40K PN1.6, 4.0, 6.4MPa Connection type Flange...

Nowadays, the valve market is mixed, and illegal traders pretend to be innovative valves to be shoddy in order to make huge profits, which brings great safety risks to the installation project. Therefore, it is necessary to introduce to you the inspection of innovative valves. At present, the valve market dealers mainly exist in the valve counterfeiting ...

1. When the sealing surface is grinding, the grinding tools, abrasives, abrasive cloth and sandpaper and other objects should be selected in a reasonable grinding method, and the coloring inspection should be carried out after grinding, and the sealing surface should be free of indentations, cracks, scratches and other shortcomings; Second, the connection between the valve stem and the closure should meet the planning requirements, and the top center is not suitable.

1. Pole change speed regulation This speed regulation method is to change the number of stator pole pairs of the cage motor to achieve the speed regulation intention by changing the wiring method of the stator winding, and the characteristics are as follows: it has hard mechanical characteristics and good stability; No slip loss, high power; The wiring is simple, the operation is convenient, and the price is ...

Valve is a kind of commonly used hardware products, the valve also has certain technical requirements before assembling and in the process of the device, otherwise the assembled valve may not reflect its own excellent function, what are the technical requirements of the valve in the assembly process? ...

The angular displacement of the valve position detected by the valve limit switch box changes the transmission shaft through the coaxial adjacency or the reaction rod, so that the cam touches the miniature switch, so that the contact of the switch assembly is closed or disconnected, and the switching signal is transmitted to the outside through the terminal, and the passer is displayed on the spot. ...

Valve application requirements (1) General gate valves, ball valves, and globe valves are prohibited from dispatching according to their structural characteristics. However, in process design, it is widely used for mediation. Because of the scheduling application, the valve seal has been in a throttling state for a long time, and the impurities in the oil have washed the seal, endangering the seal.

1. Smooth mechanism Smoothing is to add a smoothing agent between the two conflict surfaces of relative motion, so that a smooth film is formed between the two conflict surfaces, and the dry conflict appearance that is originally directly touched is separated, and the dry conflict is a conflict between the smooth agent molecules, so as to reduce the conflict and reduce wear, ...

Classified by role and use (1) Shut-off valve: The shut-off valve, also known as the closed-circuit valve, has the effect of turning on or cutting off the medium in the pipeline. Shut-off valves include gate valves, globe valves, plug valves, ball valves, butterfly valves and diaphragms. (2) Check valve: Check valve is also known as check valve or check valve.

Generally, the selection of control valve is mainly based on the nature of the medium, process parameters, use requirements, etc. 1. The properties of the medium should be clearly attributed to which of the following: (1) General fluids (2) High viscosity, fluids containing suspended solids, fibrous and other fluids (3) Toxic or high...

The valve is a control component in the fluid transportation system, which has the functions of shut-off, conditioning, diversion, preventing backflow, stabilizing pressure, diverting or overflowing pressure relief. Valves for fluid control systems, from the simplest shut-off valves to the most chaotic valves used in automated control systems, range from ...

The flow rate and velocity of the valve mainly depend on the diameter of the valve, and are also related to the resistance of the structure of the valve to the medium, and at the same time have an intrinsic relationship with the pressure, temperature and concentration of the medium of the valve. Two...

1. Impurities are stuck on the sealing surface of the valve The valve is sometimes closed suddenly, it may be that there are impurities stuck between the sealing surface of the valve, at this time should not be forced to close, the valve should be opened slightly larger, and then try to close, try repeatedly, it can generally be eliminated, otherwise it should be checked again...