Honeywell/Honeywell Proximity Sensor 21FW-74 Current 25mA

honeywell Honeywell Sensors JSM802ED3C2 Cylindrical Sensors JSM8 Series Rated: 12VDC-24VDC Load current: ≤100mA Inductive Proximity Sensors: Rectangles: JPA17 series, JPA25 series, JPA30 series, JPA40 series Cylindrical: ...

Introduction: Honeywell Humidicon Digital Humidity/Temperature Sensor: HIH6000 Series, I2C, ±4.5% RH accuracy, SIP 4-pin, no filter, 100 sensors on tape and reel. Products...

Compensatory. Calibrated with mV output. Low noise. Small form factor and high impedance. Corrosion-resistant. Primary performance. Pressure ranges from 1 psi to 100 psi The SDX series sensors provide a cost-effective solution for pressure applications that require small size and high performance. These have been proofread ...

Magnetoresistive digital position sensor. Plastic threaded sleeve encapsulation. Current sink output The SR4 series magnetoresistive digital position sensors are housed in a 14 mm cylindrical plastic housing; It supports current sink output and DC power supply This article introduces the Honeywell/Honeywell value-added packaged sensor SR4 ...

Digital Hall-effect position sensor. Plug-in and paper-mounted housing. Current sink output The SR13/15 series offers an improved package that allows for quick and easy sensor mounting while increasing the usability of the SS400 series. These sensors can be installed without the use of additional mounting hardware. ...

The Honeywell S-Series gas sensors mainly include CLE series and LEL series. CLE series: Electrochemical gas sensor, which is a microfuel cell element, developed on the basis of the original oxygen sensor. Because of its low power consumption, good selectivity, high sensitivity and ...

The MG series magnets can be used as actuators for Hall-effect and magnetoresistive sensor integrated circuits with unipolar or omnipolar magnetic characteristics. Available in a wide range of compact configurations, strengths, and magnetic materials, the MG Series magnets can be used as actuators for unipolar or omnipolar magnetic applications.

Summary: The SSC series is capable of performing comprehensive calibration and temperature compensation for sensor zero, sensitivity, temperature coefficient, and nonlinearity using an application-specific integrated circuit (ASIC) on the circuit board. Calibrated analog output values and digital outputs are updated at a rate of approx. 1 kHz and 2 kHz, respectively ...

honeywell sensors JM1204ED2Y cylindrical sensors JSM8 series Rated: 12VDC-24VDC Load current: ≤100mA Inductive Proximity Sensors: Rectangles: JPA17 series, JPA25 series, JPA30 series, JPA40 series Cylindrical: J ...

Description: The Honeywell TruStability TSC Series is a piezoresistive silicon pressure sensor that provides a proportional analog output for providing pressure readings over a specified full-scale pressure span and temperature range. The TSC series sensors are intended for use in non-corrosive and non-corrosive applications such as air...

Summary: The HSC series is capable of performing comprehensive calibration and temperature compensation for sensor zero, sensitivity, temperature coefficient, and nonlinearity using an application-specific integrated circuit (ASIC) on the board. Calibrated analog output values and digital outputs are updated at a rate of approx. 1 kHz and 2 kHz, respectively ...

HONYWELL DPT2500U1-B Sensors DPT Series Air Differential Pressure Sensors Honeywell's DT series of micro differential pressure transmitters are designed to measure differential or gauge pressure, and are available in a wide range of ranges as low as +/-50Pa and as high as 0-l0kPa, suitable for: VAC HVAC, Smart Building Energy...

Introduction: Honeywell Humidicon Digital Humidity/Temperature Sensor: HIH6000 Series, I2C, ±4.5% RH accuracy, SIP 4-pin, no filter, 100 sensors on tape and reel. Give birth...

Introduction: 200FW Series, Shielded 3-Wire DC Current Sink Output (NPN), NC Proximity Sensor, 0.625 Inch Cylindrical Housing , 20 ga, MIL-W-22759/7 Wire 2.4 mm to 11.4 mm [.09 in to .45 in] with 101MG7 Magnetic Target

Honeywell's 13 mm series stainless steel pressure transducers are designed for high-pressure applications that require the measurement of hazardous media in harsh environments. The series features Honeywell's proven piezoresistive semiconductor sensor chips in an oil-filled isolated housing, with or without ...

Paired large glass probes. -60°C to 300°C [-76°F to 572°F] The 129 Series thermistors are designed with precision sensing elements that require curve-fitting interchangeability for precision temperature control and precision temperature indication. These products are highly reliable and consist of a pair of ...

Introduction: The HAF series compensates for a temperature range of 0 °C to 50 °C [32 °F to 122 °F] and can operate in a temperature range of -20 °C to 70 °C [-4 °F to 158 °F]. Advanced ASIC-based compensation enables digital (I...

Introduction: The HAF series compensates for a temperature range of 0 °C to 50 °C [32 °F to 122 °F] and can operate in a temperature range of -20 °C to 70 °C [-4 °F to 158 °F]. Advanced ASIC-based compensation enables digital (I...

Digital pressure indicator. High pressure type, 15 psi to 60,000 psi. Accuracy: 0.1% FS This model includes a pressure sensor and digital readout combination and is designed for industrial and laboratory applications. Accu-Gage offers portability, high accuracy, industrial-grade durability, and a highly competitive ...

Summary: The HSC series is capable of performing comprehensive calibration and temperature compensation for sensor zero, sensitivity, temperature coefficient, and nonlinearity using an application-specific integrated circuit (ASIC) on the board. Calibrated analog output values and digital outputs are updated at a rate of approx. 1 kHz and 2 kHz, respectively ...