Alarm code: A01 System message: Open the cabinet door The cause of the Rittal air conditioner: the opening and closing of the door is not in the correct position Diagnostic method: Check the changing position of the door and, if necessary, the connection status Alarm code: A02 System message: The temperature in the cabinet is too high ...

One. The nature is different Distribution box: There is a large amount of parameter data in the distribution box. It generally constitutes a low-voltage distribution box. Control cabinet: The control cabinet is to assemble the switch cabinet, measuring instruments, protection devices and auxiliary equipment in a closed or semi-enclosed metal cabinet or screen according to the requirements of electrical wiring.

1. Make sure that all equipment in the electrical control cabinet is well grounded, and use short and thick grounding wires to connect to the common grounding point or grounding busbar. Any control equipment connected to the inverter should be co-grounded with it, and likewise ground with short and thick wires; 2. Flat conductors are used, e.g. ...

Display parameters: The control panel can display various parameters of the inverter, such as input/output voltage, current, frequency, speed, etc. Parameter setting: The control panel can set various parameters of the inverter, such as operating mode, frequency range, acceleration time, deceleration time, etc. ...

1. Press and hold the H4 button for 5 seconds to enter programming mode and ST will be displayed on the screen. 2. Click the H4 button to display 35 on the screen, then click the H2 button to display Cod on the screen, and then click the H2 button continuously to display from 0 to 22 on the screen. 3. Click H2/H3 and press ...

1. It is not displayed at that time. Solution: Check whether the sample signal cable is not connected. 2. Whether the fuse core of the controller in the cabinet is burned out. Solution: Remove the burned out fuse core and replace it with a new one. 3. The voltage of the distribution cabinet is too high, and the overvoltage alarm. Workaround: Re...

The fault codes for Rittal cabinet air conditioners are: F1, F2, F3, FF, EH, EP, EL, SF, HC. F1, F2, F3 represent improper use or failure of internal components; FF stands for Regulation Circuit Fault; EH stands for High Temperature Fault; EP stands for Actuator Failure; ...

1. The power cords of the two cabinets are connected to the power socket at the rear of the cabinet. 2. The RS232 interface of the two cabinets is connected together with a communication cable. 3. Lock the door of the main cabinet, and turn on the power from the cabinet and the main cabinet in turn. ...

1. A01 system message: open the cabinet door Rittal air conditioner Cause: the position of the door opening and closing is incorrect; 2. A02 system message: the temperature in the cabinet is too high: the refrigeration capacity is too low or small; 3. A03 System Message: Filter Monitoring Cause: Dirty Filter Diagnosis ...

Product Introduction Brand: Rittal cabinets Product model 6380.510 Aluminum box, strong thermal conductivity, excellent passive heat dissipation. For relatively small panels and control schemes. The ultra-slim design matches the embedded device and takes up almost no space. Type: Support ...

1. Improve the environment inside and outside the cabinet 1. We not only need to keep the electrical cabinet dry and clean, but also need to do a good job of cleaning and sanitation in the distribution room where the distribution cabinet is placed to prevent water and dust from entering the cabinet 2. The lighting environment of the distribution cabinet should be good, and it should be equipped with professional cabinet lighting ...

1. Avoid light The server is required to operate in a constant temperature environment, and direct sunlight will increase the temperature in the computer room, which will damage the display and shorten its service life. When operating in IDC and ISP data centers, it is impossible to see a ray of sunshine. So, in ...

1. Set the target temperature: the default temperature of the original factory is 35°C, you can press and hold the set button for more than 1 second after starting, the parameters start to flash, complete the temperature adjustment by pressing the UP and DOWN buttons, and after adjusting to the target temperature, press the set button to store the set parameters. 2. High temperature alarm: ...

1. E0: Indoor temperature sensor is faulty. When this fault code appears, you need to check whether the indoor temperature sensor is working properly. 2. E1: Outdoor temperature sensor failure. When this fault code appears, you need to check whether the outdoor temperature sensor is working properly. 3. E2 ...

1. Determine the size of the server, such as depth size, height size (how many U), and whether it is a 19-inch rack-mounted installation. 2. Choose a cabinet according to the installation space: If the server is a 19-inch rack-mounted installation, then a standard cabinet can be used. Root...

Rittal for AE Product model 2733.000 Retrofit on AE in place of a door, or on a sufficiently large flat surface. Product Description: For retrofitting on AE instead of doors and flat surfaces Material: Frame: Aluminum, by natural aluminium anode

A01--- Rittal cabinet control cabinet door opens View: Look at the door switches in the Rittal cabinet. Solution: (1) Adjust the position of the door switch. (2) Check whether the wiring method is correct (passive normally closed point at 1.2 points). A03 --- Filter Monitor ...

1. It can be installed in places where dangerous gases exist, and it is safe to use the control cabinet in some environments with gas or vapor gas. 2. The shell of the control cabinet is generally made of steel plate welding or cast aluminum alloy die-casting, with high-voltage electrostatic spraying, and the whole is made of flameproof type.

1. Tie the cable tie at the beginning of the root of the cable with a cable tie, if there are too many cables, the number of the network cable is divided into two or many parts from the center, but the demand ensures that each part of the network cable is connected, because the next step is simple. 2. According to ...

1. E1: Temperature sensor failure 2. E2: Humidity sensor malfunction 3. E3: Compressor overload protection 4. E4: Compressor phase loss protection 5. E5: Compressor short circuit protection 6. E6: Compressor switch failure 7. E7: Fan failure ...

1. Power failure: The power supply of the fan fails, such as the power cord is disconnected, the power plug is loose, etc., which will cause the current to fail to transmit normally, resulting in the fan stopping and rotating. 2. The temperature is too low: Some heat dissipation windbreakers have a temperature protection function, when the temperature is too low, the fan will automatically ...